Filter
Top Products
Reelmaster 7000Hydraulic System Page 4 -- 72
Filtering Closed--Loop Traction Circuit
Filtering ofa closed--loop hydraulic systemafter a major
component failure (e.g. traction (piston) pump or front
wheel motor) is a requirement to prevent debris from
transmitting throughout the system. If a closed--loop hy-
draulic system filtering tool isnot used to ensure system
cleanliness,repeatfailures,as wellassubsequentdam-
age to other hydraulic components in the affected sys-
tem, will occur. To effectively remove contamination
from closed--loop traction circuit, use of the Toro high
flow hydraulic filter and hydraulic hose kits are recom-
mended (see Special Tools in this chapter).
1. Parkmachine onalevel surfacewith enginestopped
and key removed from ignition switch.
2. Raise and support machine so all wheels are off the
ground (see Jacking Instructions inChapter 1 -- Safety).
NOTE: If front wheel or rear axle motor was replaced,
install high flow filter to the inlet of new motor instead of
to thetraction pumpfitting.This will preventsystem con-
tamination from entering and damaging the new motor.
3. Thoroughly clean junction of hydraulic hose and
right side fitting on bottom of traction pump (Fig. 50).
Disconnect hose from right side pump fitting.
4. Connect Toro high flow hydraulic filter in series be-
tween traction pump fitting and disconnected hose. Use
hydraulic hose kit (see Special Tools in this chapter) to
connectfilterto machine.Makesurethatfittingand hose
connections are properly tightened.
IMPORTANT: Use only hydraulic fluids specified in
Operator’sManual.Otherfluids couldcausesystem
damage.
5. After installing high flow filter to machine, check and
fill hydraulic reservoir withnew hydraulic oil as required.
6. Start engineand run at idle speed. Check for any hy-
draulic leakage from filter and hose c onnections. Cor-
rect any leaks before proceeding.
CAUTION
Allwheels willbe off theground androtating dur-
ing this procedure. Make sure machine is well
supported so it will not move and accidentally
fall to prevent injuring anyone around machine.
IMPORTANT: While engaging the traction circuit,
monitor the indicator on the high flow hydraulic fil-
ter. If the indicator should show red, either reduce
pressure on the traction pedal or reduce engine
speed to decrease hydraulic flow through the filter.
7. With engine running at low idle s peed, slowly move
the traction pedal to the forward direction to allow flow
throughthe tractioncircuit andhigh flowfilter.Keep trac-
tion circuit engaged for five (5) minutes while gradually
increasing both forward pressure on traction pedal and
engine speed. Monitor filter indicator to make sure that
green color is s howing during operation.
8. With engine running at high idle speed and traction
pedal moved to the forward direction, periodically apply
brakes to increase pressure in traction circuit. While
monitoring filter indicator, continue this process for an
additional five (5) minutes.
IMPORTANT: If using afilter thatis not the bi--direc-
tional Toro high flow filter, do not press the traction
pedal in the reverse direction. If flow is reversed
when using a filter that is not bi--directional, debris
from the filter will re --enter the traction circuit.
9. With engine running at high idle speed, alternately
movetractionpedalfromforward toreverse.Whilemon-
itoring filter indicator, continue this process for an addi-
tional five (5) minutes.
10.Shut engine offand removekey from ignition switch.
11.Remove high flow hydraulic filter and hydraulichose
kit from machine. Connect hydraulic hose to right side
traction pump fitting. Make sureto properly tighten hose
(see Hydraulic Hose and Tube Installation in the Gener-
al Information section of this chapter).
12.Lower machine to ground.
13.Check oil level in hydraulic reservoir and add correct
oil if necessary.
1. Piston (traction) pump 2. Right side fitting/hose
Figure 50
FRONT
RIGHT
1
2