Kohler 20-3250 kW Portable Generator User Manual


 
TP-6200 10/1244 Section 2 Operation
Menu List Summary, continued (Legend: D First level submenu, d second level submenu)
Menu 9
Input Setup
Menu 9
Input Setup, cont.
Menu 7
Generator System
D Operating Mode
d Standby Y/N
d Prime Power N/Y
D System Voltage
Line-Line
D System Frequency
D Phase
d 3-Phase Delta Y/N
d 3-Phase WYE N/Y
d 1-Phase N/Y
D kW Rating
D Rated Current
D Load Shed Output
d Time Delay
D Overvoltage
d Time Delay
D Undervoltage
d Time Delay
D Overfrequency
D Underfrequency
D Overspeed
D Battery Voltage
d 12 VDC Y/N
d 24 VDC N/Y
D Low Battery Voltage
D High Battery Voltage
D Block Heater ON
[
D Block Heater OFF [
D Enable VSG Y/N [
D Enable DSC [
D Metric Units Y/N
D Set NFPA110 Defaults Y/N
[ DDC/MTU engine
w/MDEC/ADEC only
Menu 8
Time Delays
D Time Delay
Engine Start
D Time Delay
Starting Aid
D Time Delay
Crank On
D Time Delay
Crank Pause
D Time Delay
Eng. Cooldown
D Cooldown Temperature
Override Y/N
D Overcrank Shutdown
Crank Cycles
D Time Delay
Overvoltage
D Time Delay
Undervoltage
D Time Delay
Load Shed kW
Setup Analog
Auxiliary Inputs
D Analog Input
(Scroll through up to 7
user-defined descriptions.
See Figure 2-8 in User
Inputs for factory-reserved
inputs that are not user-
selectable.)
D Analog Input
Warning Enabled Y/N
D Analog Input
Shutdown Enabled Y/N
D Analog Input
Inhibit Time 0--60 Sec.
D Analog Input
Warning Delay Time
0--60 Sec.
D Analog Input
Shutdown Delay Time
0--60 Sec.
D Analog Input
Low Shutdown Value
D Analog Input
Low Warning Value
D Analog Input
High Warning Value
D Analog Input
High Shutdown Value
Menu 10
Output Setup
Defined Common Fault
D Defined Common Fault
(Y/N for a single defined
common fault)
Scroll through status and
fault choices from:
d System events,
see Group B (except
Defined Common Fault)
d 21 digital inputs
D01-D21
d 7 analog inputs
A01--A07
Setup Digital
Auxiliary Inputs
D Digital Input
(Scroll through up to 21
user-defined
descriptions. See
Figure 2-8 in User Inputs
for factory-reserved
inputs that are not user-
selectable.)
D Digital Input
Message Text Y/N,
see Group A
Group A
Preprogrammed
selections include the
following:
Warning
Shutdown Type A
Shutdown Type B
Voltage Raise
Voltage Lower
VAR PF Mode
Remote Shutdown
Remote Reset
Air Damper
Low Fuel
Field Overvoltage
Idle Mode Active
(ECM engines only)
Battle Switch
Ground Fault
Bat Chgr Fault
High Oil Temperature
(non-ECM only)
Low Coolant Level
Low Coolant Temperature
(Not user-selectable)
Breaker Closed, (Paralleling
non-selectable)
Enable Synchronizer,
(Paralleling
non-selectable)
Air/Fuel Module Shutdown*
Knock Shutdown*
Detonation Warning*
Detonation Shutdown*
Low Fuel Shutdown
D Digital Input
Enable Y/N
D Digital Input
Inhibit TIme
D Digital Input
Delay Time
*Waukesha engine only
Menu 10
Output Setup, cont.
Relay Driver Outputs
(RDOs)
D RDOs (Y/N)
(Scroll through up to
31 status and fault choices
from:
d System events,
see Group B
d 21 digital inputs
D01-D21
d 7 analog inputs
A01--A07
Group B
System events include the
following:
Emergency Stop
Over Speed
Overcrank
High Cool Temp Shutdown
Oil Pressure Shutdown
Low Coolant Temperature
(non-ECM engines)
Low Fuel Warning
Hi Cool Temp Warning
Oil Pressure Warning
Master Not in Auto
NFPA 110 Fault
[
[
The 15 NFPA 110 Common
Fault Alarms include the
following:
Over Speed
Overcrank
High Coolant Temperature
Shutdown
Oil Pressure Shutdown
Low Coolant Temperature
High Coolant Temperature
Warning
Oil Pressure Warning
Low Fuel
Master Not In Auto
Battery Charger Fault
Low Battery Voltage
HIgh Battery Voltage
Low Coolant Level
EPS Supplying Load
Air Damper Indicator