Filter
Top Products
Table of Contents
iv
AWG510 & AWG520 Service Manual
List of Figures
Figure 1–1: Dimensions 1–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–2: Signal timing 1–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–1: Menu buttons, bezel menu buttons, and the CLEAR MENU
button 2–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–2: Bottom and side menus 2–10. . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–3: Pop-up menu example 2–11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–4: Dialog box example 2–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–5: Knob icon displayed in Status Display Area 2–13. . . . . . . . . .
Figure 2–6: Keypad buttons 2–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–7: Three type of Input text dialog boxes 2–15. . . . . . . . . . . . . . . .
Figure 2–8: Shortcut controls 2–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–9: Files and directories with read only attribute 2–21. . . . . . . . .
Figure 2–10: Input Filename dialog box 2–21. . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–1: Diagnostic menu 4–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–2: Calibration result message box 4–6. . . . . . . . . . . . . . . . . . . . .
Figure 4–3: EVENT IN connector pins and signals and ground closure
connector with 9-pin D-type connector 4–14. . . . . . . . . . . . . . . . . . . . . .
Figure 4–4: Loading file; selecting storage drive 4–15. . . . . . . . . . . . . . . . .
Figure 4–5: Cont mode initial test hookup 4–23. . . . . . . . . . . . . . . . . . . . . .
Figure 4–6: Triggered mode initial test hookup 4–25. . . . . . . . . . . . . . . . . .
Figure 4–7: Relationship between trigger signal and waveform output . . . . .
4–26
Figure 4–8: Relationship between gate signal and waveform output 4–28.
Figure 4–9: Clock frequency initial test hookup 4–30. . . . . . . . . . . . . . . . .
Figure 4–10: Amplitude accuracy initial test hookup 4–32. . . . . . . . . . . . .
Figure 4–11: Direct DA out amplitude accuracy initial test hookup 4–36.
Figure 4–12: Direct DA out pulse rise time initial test hookup 4–38. . . . . .
Figure 4–13: Pulse response initial test hookup 4–40. . . . . . . . . . . . . . . . . .
Figure 4–14: Sine wave initial test hookup 4–43. . . . . . . . . . . . . . . . . . . . . .
Figure 4–15: Internal trigger initial test hookup 4–45. . . . . . . . . . . . . . . . .
Figure 4–16: Trigger input initial test hookup 4–47. . . . . . . . . . . . . . . . . . .
Figure 4–17: Trigger Signal (+5V check1) 4–49. . . . . . . . . . . . . . . . . . . . . .
Figure 4–18: Trigger Signal (+5V check2) 4–50. . . . . . . . . . . . . . . . . . . . . .
Figure 4–19: Trigger Signal (–5V check1) 4–51. . . . . . . . . . . . . . . . . . . . . . .