Toro 30607 and 30609 Lawn Mower User Manual


 
Groundsmaster 4000--D/4010--DHydraulic System Page 4 -- 74
Filtering Closed--Loop Traction Circuit
Filtering of a closed--loop hydraulic system after a major
component failure (e.g. traction (piston) pump or front
wheel motor) is a requirement to prevent debris from
transmitting throughout the system. If ac losed--loop hy-
draulic system filtering tool is not used to ensure system
cleanliness,repeatfailures, aswell assubsequentdam-
age to other hydraulic components in the affected sys-
tem, will occur. To effectively remove contamination
from closed--loop traction circuit, use of the Toro high
flow hydraulic filter and hydraulic hose kits are recom-
mended (see Special Tools in this chapter).
1. Park machine ona levelsurface with engine stopped
and key removed from ignition switch.
2. Raise and support machine so all wheels are off the
ground (see Jacking Instructions in Chapter 1 -- Safety).
NOTE: If front wheel or rear axle motor was replaced,
install high flow filter to the inlet o f new motor instead of
to thetract ion pump fitting. Thiswill prevent system con-
tamination from entering and damaging the new motor.
3. Thoroughly clean junction of hydraulic hose and left
side fitting on bottom of p iston (traction) pump (Fig. 51).
Disconnect hose from left side pump fitting.
4. Connect Toro high flow hydraulic filter in series be-
tweenpistonpumpfittinganddisconnectedhose.Use
hydraulic hose kit (see Special Tools in this chapter) to
connectfilter tomachine. Makesure thatfittingand hose
connections are properly tightened.
IMPORTANT: When filling hydraulic reservoir, use
only hydraulic fluids specified in Operator’s Manu-
al. Other fluids could cause system damage.
5. After installing high flow filter to machine, check and
fill hydraulic reservoir with new hydraulic oil as required.
6. Start engine and run at idle speed. Check for any hy-
draulic leakage from filter and hose connections. Cor-
rect any leaks before proceeding.
CAUTION
Allwheels willbe offthe groundand rotatingdur-
ing this procedure. Make sure machine is well
supported so it will not move and accidentally
fall to prevent injuring anyone around machine.
IMPORTANT: While engaging the traction circuit,
monitor thehigh flow hydraulic filterindicator. If the
indicator should show red, either reduce traction
pedal setting or reduce engine speed to decrease
hydraulic flow through the filter.
7. With engine running at low idle speed, slowly move
thetractionpedaltotheforward direction to allow flow
throughthe traction circuit andhigh flowfilter.Keep trac-
tion circuit engaged for five (5) minutes while gradually
increasing both forward pressure on traction pedal and
engine speed. Monitor filter indicator to m ake sure that
green color is showing during operation.
8. With engine running at high idle speed and traction
pedal moved to the forward direction, periodically apply
brakes to increase pressure in traction circuit. While
monitoring filter indicator, continue this process for an
additional five (5) minutes.
IMPORTANT: If using a filter that is not the bi--direc-
tional Toro high flow filter, do not press the traction
pedal in the reverse direction. If flow is reversed
when using a filter that is not bi--directional, debris
from the filter will re--enter the traction circuit.
9. With engine running at high idle speed, alternately
movetractionpedal fromforward toreverse. Whilemon-
itoring filter indicator, continue this process for an addi-
tional five (5) minutes.
10.Shut engine off and remove key from ignition switch.
11.Removehighflowhydraulic filter and hydraulic hose
kit from machine. Connect hydraulic hose to right side
piston (traction) pump fitting. Make sure to properly
tighten hose (see Hydraulic Hose and Tube Installation
in the General Information section of this chapter).
12.Lower machine to ground.
13.Check oil level in hydraulic reservoir and add correct
oil if necessary.
1. Piston (traction) pump 2. Left side fitting/hose
Figure 51
FRONT
RIGHT
1
2