Filter
Top Products
5-28 489 Generator Management Relay GE Multilin
5.8 DIAGNOSTICS 5 ACTUAL VALUES
5
• SETPOINT ACCESS IS NOW RESTRICTED: If the passcode security feature is enabled and a valid passcode
entered, this message appears when the S1 489 SETUP Ö PASSCODE ÖØ SETPOINT ACCESS setpoint is altered to
"Restricted". This message also appears any time that setpoint access is permitted and the access jumper is removed.
• DATE ENTRY WAS NOT COMPLETE: Since the DATE setpoint has a special format (entered as MM/DD/YYYY), this
message appears and the new value will not be stored if the key is pressed before all of the information has
been entered. Another attempt will have to be made with the complete information.
• DATE ENTRY WAS OUT OF RANGE: Appears if an invalid entry is made for the
DATE (for example, 15 entered for the
month).
• TIME ENTRY WAS NOT COMPLETE: Since the TIME setpoint has a special format (entered as HH/MM/SS.s), this
message appears and the new value will not be stored if the key is pressed before all of the information has
been entered. Another attempt will have to be made with the complete information.
• TIME ENTRY WAS OUT OF RANGE: Appears if an invalid entry is made for the TIME (for example, 35 entered for the
hour).
• NO TRIPS OR ALARMS TO RESET: Appears if the key is pressed when there are no trips or alarms present.
• RESET PERFORMED SUCCESSFULLY: If all trip and alarm features that are active can be cleared (that is, the con-
ditions that caused these trips and/or alarms are no longer present), then this message appears when a RESET is per-
formed, indicating that all trips and alarms have been cleared.
• ALL POSSIBLE RESETS HAVE BEEN PERFORMED: If only some of the trip and alarm features that are active can
be cleared (that is, the conditions that caused some of these trips and/or alarms are still present), then this message
appears when a RESET is performed, indicating that only trips and alarms that could be reset have been reset.
• ARE YOU SURE? PRESS [ENTER] TO VERIFY: If the key is pressed and resetting of any trip or alarm feature
is possible, this message appears to verify the operation. If is pressed again while this message is displayed,
the reset will be performed.
• PRESS [ENTER] TO ADD DEFAULT MESSAGE: Appears if the decimal [.] key, immediately followed by the
key, is entered anywhere in the actual value message structure. This message prompts the user to press to add
a new default message. To add a new default message, must be pressed while this message is being dis-
played.
• DEFAULT MESSAGE HAS BEEN ADDED:
Appears anytime a new default message is added to the default message
list.
• DEFAULT MESSAGE LIST IS FULL: Appears if an attempt is made to add a new default message to the default mes-
sage list when 20 messages are already assigned. To add a new message, one of the existing messages must be
removed.
• PRESS [ENTER] TO REMOVE MESSAGE: Appears if the decimal [.] key, immediately followed by the key, is
entered in the
S1 489 SETUP ÖØ DEFAULT MESSAGES setpoint page. This message prompts the user to press to
remove a default message. To remove the default message, must be pressed while this message is being dis-
played.
• DEFAULT MESSAGE HAS BEEN REMOVED: Appears anytime a default message is removed from the default mes-
sage list.
• DEFAULT MESSAGES 6 of 20 ARE ASSIGNED: Appears anytime the S1 489 SETUP ÖØ DEFAULT MESSAGES setpoint
page is entered, notifying the user of the number of default messages assigned.
• INVALID SERVICE CODE ENTERED: Appears if an invalid code is entered in the S12 489 TESTING ÖØ FACTORY SER-
VICE setpoints page.
• KEY PRESSED HERE IS INVALID:
Under certain situations, certain keys have no function (for example, any number
key while viewing actual values). This message appears if a keypress has no current function.
• DATA CLEARED SUCCESSFULLY: Confirms that data is reset in the
S1 489 SETUP ÖØ CLEAR DATA setpoints page.
• [.] KEY IS USED TO ADVANCE THE CURSOR: Appears immediately to prompt the use of the [.] key for cursor con-
trol anytime a setpoint requiring text editing is viewed. If the setpoint is not altered for 1 minute, this message flashes
again.
• TOP OF PAGE: This message will indicate when the top of a page has been reached.
• BOTTOM OF PAGE: This message will indicate when the bottom of a page has been reached.
ENTER
ENTER
RESET
RESET
RESET
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER