Filter
Top Products
S205 Skid-Steer Loader
109 Operation & Maintenance Manual
DIAGNOSTIC SERVICE CODES (CONT’D)
Service Codes List (Cont’d)
CODE CODE
39-04 Left joystick no communication to Bobcat controller 75-22 Right Joystick Y-Axis Out of Range High (H-Pattern
Only)
75-27 Left Swash Plate Out of Position
40-04 Right joystick no communication to Bobcat controller 75-28 Right Swash Plate Out of Position
75-29 Left Joystick X-Axis Out of Range Low
44-02 Horn error ON 75-31 Left Joystick Y-Axis Out of Range Low
44-03 Horn error OFF 75-32 Right Joystick Y-Axis Out of Range Low (H-Pattern
Only)
75-37 5 Volt Sensor Supply 1 Out of Range Low
45-02 Right blinker error ON 75-39 Left Swash Plate Sensor Out of Range High
45-03 Right blinker error OFF 75-40 Left Swash Plate Sensor Out of Range Low
75-41 Right Swash Plate Out of Range High
46-02 Left blinker error ON 75-42 Right Swash Plate Sensor Out of Range Low
46-03 Left blinker error OFF 75-43 Left Forward Drive Solenoid Error ON
75-44 Left Reverse Drive Solenoid Error ON
47-21 8 volt sensor supply out of range high 75-45 Right Forward Drive Solenoid Error ON
47-22 8 volt sensor supply out of range low 75-46 Right Reverse Drive Solenoid Error ON
75-52 Backup Alarm Error ON
48-02 Front light relay error ON 75-53 Left Forward Drive Solenoid Error OFF
48-03 Front light relay error OFF 75-54 Left Reverse Drive Solenoid Error OFF
75-55 Right Forward Drive Solenoid Error OFF
49-02 Rear light relay error ON 75-56 Right Reverse Drive Solenoid Error OFF
49-03 Rear light relay error OFF 75-66 Backup Alarm Error OFF
75-67 No Communication from Bobcat Controller
60-21 Rear auxiliary control out of range high 75-69 Battery Voltage Out of Range High
60-22 Rear auxiliary control out of range low 75-70 Interrupted Power (also occurs after software
updates)
60-23 Rear auxiliary control not returning to neutral 75-71 Battery Voltage Out of Range Low
75-72 Drive Pump Not Calibrated
64-02 Switched power relay error ON 75-73 ISO / H Pattern Switch Flipped While Operating
64-03 Switched power relay error OFF 75-74 Right Wheel Speed Uncommanded Motion
75-75 Left Wheel Speed Uncommanded Motion
74-72 Bobcat controller in boot code 75-76 No Communication from ACS Controller
74-73 Left hand panel system RX error 75-77 Left Speed Sensor Out of Range High
75-78 Right Speed Sensor Out of Range High
75-4 No Communication from Drive Controller 75-79 Left Speed Sensor Out of Range Low
75-5 Left Joystick X-Axis Not in Neutral 75-80 Right Speed Sensor Out of Range Low
75-7 Left Joystick Y-Axis Not in Neutral 75-85 5-Volt Sensor Supply 1 Out of Range High
75-8 Right Joystick Y-Axis Not in Neutral (H-Pattern Only) 75-91 Left Swash Sensor Reversed
75-9 ISO / H Pattern Switch Short to Ground or Battery 75-92 Right Swash Sensor Reversed
75-17 Left Swash Plate Not in Neutral 75-93 Unresponsive Right Speed Sensor
75-18 Right Swash Plate Not in Neutral 75-94 Unresponsive Left Speed Sensor
75-21 Left Joystick Y-Axis Out of Range High 75-95 Left Speed Sensor Reverse Direction
75-19 Left Joystick X-Axis Out of Range High 75-96 Right Speed Sensor Reverse Direction
75-21 Left Joystick Y-Axis Out of Range High (H-Pattern
Only)
75-98 Controller in Calibration Mode