Filter
Top Products
Voice Mode
MOTIF-RACK XS Owner’s Manual
70
Basic Structure
Reference
Voice
Multi Utility
The Controls &
Connectors
Setting Up
Listening to
the Sound
Connections
Using a Computer
Quick Guide
Appendix
Delay Time Determines the delay time between the moment a Note On message is received and the moment the
LFO takes effect. A higher value results in a longer delay time.
Settings: 0 – 127
Fade in Time Determines the amount of time for the LFO effect to fade in after the Delay time has elapsed. A
higher value results in a slower fade-in. When set to “0,” the LFO effect will not fade in and reach the
maximum level immediately after the Delay time has elapsed.
Settings: 0 – 127
Hold Time Determines the length of time for which the
LFO is held at its maximum level. A higher
value results in a longer Hold time. A
setting of hold produces no fade out.
Settings: 0 – 126, hold
Fade out Time Determines the amount of time for the LFO effect to fade out (after the Hold time has elapsed). A
higher value results in a slower fade-out.
Settings: 0 – 127
LFO Set 1 – 3 Dest
(LFO Set 1 – 3 Destination)
Determines the parameters which are to be controlled (modulated) by the LFO Wave. Three
Destinations can be assigned, and you can choose from several parameters per Destination.
Settings: insA1 – insA16, insB1 – insB16, A mod, P mod, F mod, reso, pan, LFOspd
insA1 – insA16, insB1 – insB16, (Effect parameters)
Each parameter of the selected Effect type is modulated cyclically. When one of those parameters is selected, the
corresponding parameter name of the selected Effect type is shown in the display.
A mod (Amplitude Modulation Depth)
A tremolo effect produced by cyclically modulating the volume.
P mod (Pitch Modulation Depth)
A vibrato effect produced by cyclically modulating the pitch.
F mod (Filter Modulation Depth)
A wah effect produced by cyclically modulating the tonal brightness.
reso (Resonance)
A special wah effect produced by cyclically modulating the resonance.
pan
An effect produced by cyclically modulating the stereo pan position.
LFOspd (Element LFO Speed)
When this is selected, the Common LFO speed cyclically modulates the Element LFO speed.
n If one or more “LFO Set 1 – 3 Element Sw” is set to “off” in the one set on the MOTIF-RACK XS Editor and this
parameter is set to something other than one of the effect parameters, “!” indications are shown at right of the “LFO
Set 1 – 3 Dest” and “LFO Set 1 – 3 Depth” settings. This “!” mark indicates that the settings do not apply to all
Elements.
LFO Set 1 – 3 Depth Determines the LFO Wave Depth for each set.
Settings: 0 – 127
LFO Set 1 – 3 Element Sw Determines whether or not each Element is to be affected by the LFO on the MOTIF-RACK XS Editor.
When some buttons are set to “on”, the appropriate Elements are to be affected by the LFO.
LFO Set 1 – 3 Depth Offset Determines the offset values of the “LFO Set 1 – 3 Depth” parameter (above) for the respective
Elements on the MOTIF-RACK XS Editor. If the resultant “LFO Set 1 – 3 Depth” value is less than zero
it will be set to 0, and if the resultant “LFO Set 1 – 3 Depth” value is greater than 127 it will be set to
127.
Settings: 0 – 127
LFO Phase Offset Determines the offset values of the “Phase”
parameter in the Wave for the respective
Elements on the MOTIF-RACK XS Editor.
Settings: 0°, 90°, 120°, 180°, 240°, 270°
User LFO Cycle Determines the amount of steps for creating the wave on the MOTIF-RACK XS Editor.
Settings: 2, 3, 4, 6, 8, 12, 16
User LFO Slope Determines the slope or ramp characteristics of the LFO wave on the MOTIF-RACK XS Editor.
Settings: off, up, down, up&down
off ...................................... Creates no slope.
up...................................... Creates an upward slope.
down.................................. Creates a downward slope.
up&down........................... Creates an upward then downward slope.
Fade in
Max
Time
Fade out
Hold
0° 90°
120°
240°
180° 270°
Phase
Time