Filter
Top Products
PROGRAMMING AND OPERATION
32
MENUS (For the Installer Menu, press and hold SELECT button for approximately 13 seconds to access this feature)
Programming the language for the display (Allows for personal preference language display)
1. Press MENU, press
∆ or ∇ until “Owner or Installer Menu” is displayed, then press SELECT.
2. Press
∆ or ∇ until “Select language” is displayed, then press SELECT (English is the factory setting).
3. Press
∆ or ∇ until desired language “English”, “Spanish”, “French”, or “German” is displayed, then press SELECT.
4. Press
∆ or ∇ until “End menu mode” is displayed, then press SELECT.
Programming the liquid and weight measurement units for the display (Allows for personal preference units display).
1. Press MENU, press
∆ or ∇ until “Owner or Installer Menu” is displayed, then press SELECT.
2. Press
∆ or ∇ until “Select units” is displayed then press SELECT (English units is the factory setting).
3. Press
∆ or ∇ until desired measurement “English units” (gallons and pounds) or “Metric units” (liters and kilograms) is
displayed, then press SELECT.
4. Press
∆ or ∇ until “End menu mode” is displayed then press SELECT.
Programming the temperature measurement unit for the display (Allows for personal preference temperature display).
1. Press MENU, press
∆ or ∇ until “Owner or Installer Menu” is displayed, then press SELECT.
2. Press
∆ or ∇ until “Temperature unit” is displayed, then press SELECT (Fahrenheit is the factory setting).
3. Press
∆ or ∇ until desired measurement unit “Fahrenheit” or “Celsius” is displayed then press SELECT.
4. Press
∆ or ∇ until “End menu mode” is displayed then press SELECT.
Programming the time format to 12 / 24 hour clock for the display (Allows fo r pers o nal preference time clock display).
1. Press MENU, press
∆ or ∇ until “Owner or Installer Menu” is displayed, then press SELECT.
2. Press
∆ or ∇ until “12/24 hour clock” is displayed, then press SELECT (12 hour is the factory setting).
3. Press
∆ or ∇ until desired time format “12 hour” or “24 hour” is displayed, then press SELECT.
4. Press
∆ or ∇ until “End menu mode” is displayed then press SELECT.
Programming the time of day (Allows for changes to the time of day displays for time zones or day-light savings).
1. Press MENU, press ∆ or ∇ until “Owner, Maintenance Menu, or Installer Menu” is displayed, then press SELECT.
2. Press
∆ or ∇ until “Set time of day” is displayed, then press SELECT (Eastern standard time is the factory setting).
3. Press
∆ or ∇ until the desired hour is displayed, then press SELECT.
4. Press
∆ or ∇ until the desired minutes are displayed, then press SELECT.
5. Press
∆ or ∇ until “End menu mode” is displayed, then press SELECT.
Programming the operating times for a pump controlled by the Pool Pilot Relay (two pump program modes available)
(
This feature is only available when “Set Relay 1” is programmed for a one-speed or two-speed pump.)
Caution:
Do not overlap Pump Program 1 and Pump Program 2 times as the unit will perform the earliest ON and OFF times,
which may cause decreased pump run times..
1. Press MENU, press ∆ or ∇ until “Owner, Maintenance Menu, or Installer Menu” is displayed, then press SELECT.
2. Press
∆ or ∇ until “Pump Program 1” or “Pump Program 2” is displayed, then press SELECT (Any programmed time
will display briefly, and then toggle to the options menu).
3. A. Press
∆ - Prog to program the pump times
i. Program the Pump on time (or High speed start time)
a. Press
∆ or ∇ to adjust the hour up or down. Press SELECT when hour is correct.
b. Press
∆ or ∇ to adjust the minutes up or down. Press SELECT when minutes are correct.
ii. Program the Pump off time (or Low speed start time)
a. Press
∆ or ∇ to adjust the hour up or down. Press SELECT when hour is correct.
B. Or press
∇ - Delete to delete the current pump program
C. Or press SELECT to leave program unchanged
4. Press
∆ or ∇ until “End menu mode” is displayed, then press SELECT.