Filter
Top Products
EURO • Printed in England • GB • F016 L69 838 • CLUB/ROYALE • OSW 08/01
English - 3
3. Add a good-quality SAE 30 API SF in small quanti-
ties at a time, allowing it to settle. Repeatedly add
oil and check the level until it reaches the dip
stick 9. The engine may require up to 0.6 litres of
oil.
4. Refit and tighten the oil filler dip stick 9.
Petrol
Petrol deteriorates over time. Engine starting
may be difficult if you use petrol kept for more
than 30 days. Always run the fuel tank dry when
storing over 30 days.
1. Remove the petrol filler cap 5, add unleaded petrol
to the tank, leaving approximately 6 mm of tank
space for fuel expansion.
2. Replace the petrol filler cap 5.
3. Wipe up any spilt petrol from the engine before
starting the mower.
Battery (Electric start models)
The battery is already connected. For charging see
chapter “Battery“.
Grassbox/bag
Attach/remove the grassbox as shown.
Height of cut adjustment
Club B20
Your mower has an adjustable height of cut between
2,8 – 18 mm.
The height of cut adjusted as follows:
1. Slacken bolts
10 on both sides of the mower.
2. Turn the height of cut knob 8 to achieve the re-
quired height of cut.
3. Tighten bolts 10.
Royale models
Your mower has an adjustable height of cut between
5 – 35 mm with markings spaced between as an aid
to adjustment.
Adjusting the Cutting Height
Tilt the mower back and pull plunger 11, allowing
the stand 12 to extend fully.
1. Carefully release the plunger 11 ensuring it is fully
home and rest the mower on the stand 12.
2. Slacken bolts 13 on both sides of the mower.
3. Turn the height of cut knob 8 to achieve the re-
quired height of cut and tighten bolts 13.
4. Tilt the mower back and pull plunger 11 fully.
5. Raise the mower stand 12 and carefully release the
plunger 11.
Note: For all models you may need to re-adjust the
comb after changing height of cut (see “Comb Adjust-
ment” below).
Comb Adjustment
Your mower has an adjustable comb fitted which can
be brought into use on the lower heights of cut.
The comb is adjusted as follows:
Club models
1. Slacken nuts
14.
2. Turn screws 15 until the comb tines just touch the
ground.
Note: Take care not to set the comb tines too deep.
3. While holding screw 15 tighten nuts 14 to lock the
comb in place.
Royale models
1. Slacken nut 16 and screws 17 until the comb tines
just touch the ground.
Note: Take care not to set the comb tines too deep.
2. While holding nut 16 tighten screws 17 to lock the
comb in place.
Starting and Stopping
Starting from Cold
Recoil Start Models:
1. Move the engine cut-off switch
18 to ON.
2. Move the throttle lever 19 to position .
3. Turn the petrol tap 20 on.
4. Move the choke lever 21 to “On”.
5. Pull the recoil cord handle 22. Allow the recoil
handle to return slowly after each pull.
Electric start models:
1. Move the engine cut-off switch 18 to ON.
2. Move the throttle lever 19 to position .
3. Turn the petrol tap 20 on.
4. Move the choke lever 21 to “On”.
5. Turn the key clockwise to start. If the engine
doesn’t start after three attempts use the recoil cord
handle and charge the battery (see maintenance
and also fault finding sections).
Starting from Hot
Follow “Starting from Cold” ignore steps 4 only.
If the engine does not start or will not continue to run
follow the “Starting from Cold” procedure with choke
lever between the “On” and “Off” postion.
Stopping
1. Move the throttle lever 19 to position Stop-
ping.
2. Move the engine cut-off switch 18 to OFF.
C D
C D
E
F G
Using Your mower
E
F G
I
H
I
I
H
I
H
I
CLUB/ROYALE - Buch Seite 3 Dienstag, 7. August 2001 2:41 14
15 • F016 L69 838 • TMS • 11.07.01