Filter
Top Products
8
Introduction
RCR2596, RCR2510 and RCRM2510 Rotary Cutters 312-753M
5/09/08
Land Pride
Table of Contents
Introduction
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
Owner Assistance
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Cutter.
The parts on your Cutter have been specially designed
and should only be replaced with genuine Land Pride
parts. Therefore, should your Cutter require replacement
parts go to your Land Pride Dealer.
Serial Number Plate
Refer to Figure 1:
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer. Be sure toinclude your serial and model numbers
in correspondence also. Refer to Figure 1 for the location
of your serial number plate.
Serial Number Plate Location
Figure 1
NOTE: A special point of information that the
operator must be aware of before continuing.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
16000
Land Pride welcomes you to the growing family of new
product owners.
This Cutter has been designed with care and built by
skilled workers using quality materials. Proper assembly,
maintenance, and safe operating practices will help you
get years of satisfactory use from the machine.
Application
The standard utility duty RCR2596, RCR2510 and
RCRM2510 Series Rotary Cutters are designedand built
by Land Pride to provide excellent cutting performance
on gently sloping or slightly contoured right-of ways,
pastures, set-aside-acres, and row crop fields. Their
eight and ten foot cutting widths, 2" to 12" cutting height
and ability to cut weeds and brush up to 1” diameter
make them well suited for these applications.
The RCR2596 and RCR2510 cutters operate at a PTO
speed of 540 rpm and the RCRM2510 cutter operates at
1000 rpm. A category four equal angle driveline is
available on all three models and a category four
constant velocity driveline is available on only the
RCR2510 & RCRM2510 models.
Pull-type and three-point type hitches are available. The
RCR2596 is designed for a category I or II three-point
hitch and theRCR2510 and RCRM2510 aredesigned for
a category II or III three-point hitch. All three-point
hitches are Quick-Hitch adaptable. The RCR2596 three-
point hitch requires a 45-110 hp tractor and the Pull-type
hitch requires a 30-110 hp tractor. The RCR2510 and
RCRM2510 three-point hitch requires a 50-110 hp
tractor and 35-110 hp for Pull-type.
Stump jumpers, main driveline slip-clutches, and
outboard flex couplers are also offered for driveline and
gearbox protection. Safety shields around the cutter are
offered in either chain or rubber.
See “Features and Benefits” section and “Product
Specifications” for more information and performance
enhancing options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual contact your
authorized dealer. Manuals can also be downloaded,
free-of-charge from our website at www.landpride.com
or printed from theLand Pride Service & Support Center
by your dealer.