Filter
Top Products
Section 10
SPECIFICATIONS & CHARTS
Page 77
TYPE RV 45G/LP RV 55G/LP RV 65G/LP
MODEL 5410/5411 5412/5413 5414/5415
WEIGHT 278/281 pounds 285/288 pounds 293/296 pounds
TYPE OF ROTOR Two-pole Two-pole Two-pole
RATED WATTS 4500 5500 6500
RATED VOLTS 120 120 120
PHASE 1-Phase 1-Phase 1-Phase
RATED MAX.
CONTINUOUS CURRENT
AMPS (240V)
37.5 (18.7) 45.8 (22.9) 54.1 (27)
RATED FREQUENCY 60 Hz 60 Hz 60 Hz
OPERATING SPEED 2571 rpm 2571 rpm 2571 rpm
ENGINE MODEL GT-530 GT-530 GT-530
TYPE OF ENGINE Vertical Shaft Vertical Shaft Vertical Shaft
FUEL SYSTEM Gasoline/LP Gasoline/LP Gasoline/LP
COOLING SYSTEM Air-Cooled Air-Cooled Air-Cooled
OIL SYSTEM Pressurized with Filter Pressurized with Filter Pressurized with Filter
OIL PUMP Trochoid Type Trochoid Type Trochoid Type
AIR CLEANER Paper element Paper element Paper element
STARTER 12 VDC electric 12 VDC electric 12 VDC electric
IGNITION SYSTEM Solid State/Flywheel
Magneto
Solid State/Flywheel
Magneto
Solid State/Flywheel
Magneto
SPARK PLUG NGK BPR6HS NGK BPR6HS NGK BPR6HS
SPARK PLUG GAP 0.030 inch (0.76mm) 0.030 inch (0.76mm) 0.030 inch (0.76mm)
NOMINAL RESISTANCES OF GENERATOR WINDINGS AT 68°F
GENERATOR SPECIFICATIONS
TYPE RV 45G/LP RV 55G/LP RV 65G/LP
MODEL 5410/5411 5412/5413 5414/5415
Power Windings
Lead 11 to 22
Lead 11S to 22S
Lead 33 to 44
0.376 - 0.416 ohms 0.28 - 0.32 ohms 0.209 - 0.242 ohms
Excitation “DPE” Winding
Lead 2 to 6
2.59 ohms 1.41 - 1.63 ohms 1.59 - 1.84 ohms
Rotor Winding
Slip Ring to Slip Ring
13.4 ohms 14.88 ohms 10.81 ohms
TORQUE REQUIREMENTS
(unless otherwise specified)
Stator Bolts ................................................................ 8 ft-lbs
Alternator Pulley ...................................................... 38 ft-lbs
Engine Pulley ........................................................... 38 ft-lbs
Oil Adaptor Bolt ...................................................... 4.5 ft-lbs
Oil Lines .................................................................. 70 in-lbs
Intake Manifold ........................................................ 18 ft-lbs
Exhaust Manifold ..................................................... 18 ft-lbs
M5-0.8 taptite screw into aluminum ................... 25-50 in-lbs
M5-0.8 taptite screw into pierced hole ............... 25-50 in-lbs
M6-1.0 taptite screw into aluminum ................... 50-96 in-lbs
M6-1.0 taptite screw into pierced hole ............... 50-96 in-lbs
M6-1.0 taptite screw into weldnut ...................... 50-96 in-lbs
M8-1.25 taptite screw into aluminum ................. 12-18 ft-lbs
M6-1.0 nylok nut onto stud ................................ 16-65 in-lbs
Dipstick Casting Oil Line ....................................... 250 in-lbs
Note: Torques are dynamic values with ±10 % tolerance
unless otherwise noted.