Filter
Top Products
PAGE 34 — GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #2 (11/03/08)
GB12BW/BS/BP LIGHTING SYSTEM — NAMEPLATE AND DECALS
ALWAYS hook the latch
to prevent tipping.
Lower
position
Upper
position
GB12BS
GB12BW
LAMP INFORMATION
CAUTION
NE VERallowthe lampto strike any
hard surface. Excessiveimpactcan
cause damage and reduce the service
life ofthelamp.
GB12BP
DANGER
To avoid accident or
injury ALWAYS make
certain hardware is
securely fastened on
pipe clamps.
DCL1002
DANGER
To avoid accident or
injury ALWAYS make
certain hardware is
securely fastened on
pipe clamps.
DCL1002
DANGER
ELECTRICAL SHOCK HAZARD
DANGER
When replacing lamp andto prevent electrical shock,
ALWAY Sshutdown the generator before replacing lamp.
Remember to let lamp cool before removing.Use only
recommended type lamp as listed in partsmanual.
LAMP BURN HAZARD
WARNING
To prevent burns, NEVER touch lamp
while lamp is on. Lamp surface gets
extremely hot!ALWAYS allow sufficient
time for lamp to cooldown before touching.
HIGHVOLTAGE (E-BALLAST)
DANGER
The electronic componentsofthe ballast
generatehigh voltage. NEVERperform
maitenance onthee-ballast when
connected to a power source.
DCL1261
DCL1263
WARNING
Keep clear of
pinch-point when
lowering the mast.
DANGER
CAUTION
WARNING
GloBug
INFORMATION
ALWAYSturn OFF generator
before performing maintenance.
NEVERdisconnect
theGloBugSoloJr.'s
connector when power
is applied.
The possibility exists
of Electricalshockor
equipment damage.
To preventtipping,NEVERuse
in winds that exceed 16 mph
( 7 m/ sec).
NEVERuseonaninclineof5
degrees or more. Thepossibility
of tipping exists.
Pull tripod downward at the tip
end. Put sandbagson tripodto
improve the stability.
NEVERlift the GloBug Solo Jr.
Tighten T-handle bolt securely.
ALWAYSuse the GloBug Solo
Jr.'s balloon onthe top ofmast.
NEVERoperate the GloBug Solo
Jr. in the rain.A electrical shock
could occur causingSevere
BodilyHarmorevenDeath.
NEVERgrab ortouch
alivepowercord
with wet hands,
the possibility exists
of Electricalshock,
Electrocution and
evenDeath!
To prevent burns, NEVERtouch
ballast or cover while lamp ison.
These surfaces are extremely hot!
ALWAYS allow sufficient time for
both surfaces to cool downbefore
touching.
To avoid injury, you MUST read
and understand operator's manual
before using thismachine.
Thismachinetobeoperatedby
qualifiedpersonnel only.
Ask for training as needed.
Oncelamp isturned OFF,Allow
lamp to cooldown before turning
back on. Itwill take about 5
minutes beforelamp can be
turned back on.
ALWAYSdisconnect theGloBug
Solo Jr.'s AC power cable from
generator first, before shutting
down generator.
ALWAYSturn on generator first,
before connecting the GloBug
Solo Jr.'s AC power cable to
generator.
TRIPOD DEPLOYMENT
SET
1 Undo the band and pull tripod
downward at the tip end.
2 Lift up the mast to hook the latch.
RELEASE
1 Lift up the mast and pull the band
upward to unhook the latch.
2 Hold the mast and pull the band
upward until the tripod place in stow
position.
DANGER
Make sure the power cable
from the generator is
connected to the lamp
power cable securely.
A loose connection may
cause a short circuit.
NEVERuse without hooking
the latch. The possibility exists
of tipping.
BAND
LATCH
Upper
position
Lower
position
DCL1260
DCL1262
2
2
3
4
5
6
1
NAMEPLATE AND DECALS.