Filter
Top Products
24
Section 5: Maintenance & Lubrication
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
1/07/09
Land Pride
Table of Contents
Skid Shoe Maintenance
!
WARNING
Excessive wear on skid shoes may cause inadequate operation
of cutter and create a safety hazard!
Skid shoes should be inspected at the beginning of each
cutting season and replaced when material thickness is
less than 1/8" at any point. Order only genuine Land Pride
parts from your local Land Pride Dealer.
Refer to Figure 5-2:
Replace skid shoes as follows:
1. Raise the Rotary Cutter 3" or more off the ground
and place support blocks under the cutter. Make sure
the support blocks are positioned so they will not
interfere with skid shoe installation.
2. Lower cutter onto the support blocks, place Skid Steer
in park, set park brakes, shut the Skid Steer off and
remove switch key.
Land Pride Cutter Blade Parts
Item Part No. Part Description
318-586A BLADE BOLT KIT (Contains #’s 1, 2, 5 & 6)
1 802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY
2 312-075D BLADE SPACER 16 GA. (.060")
2 312-082D BLADE SPACER 18 GA. (.048")
2 312-089D BLADE SPACER 20 GA. (.036")
2 312-808C BLADE SPACER 24 GA. (.024")
3 820-112C SC2660 CUTTER BLADE 1/2 x 4 x 25 CW
3 820-249C SC2672 CUTTER BLADE 1/2 x 4 x 29 CW
4 316-124H WELDMENT DISHPAN SC2660
4 312-811H WELDMENT DISHPAN SC2672
5 804-147C WASHER FLAT 1 HARD ASTMF436
6 803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE
3. Remove 3/8" hex lock nuts (#4), lock washers (#5), flat
washers (#6), 3/8” plow bolts (#3), three skid shoes
(#1) and one skid shoe (#2) from all four deck corners.
4. Plow bolts should be checked for wear and replaced if
necessary.
5. Install the new short skid shoe (#2) to the back left
deck corner as shown with 3/8”-16 x 1 1/4 GR5 plow
bolts (#2), flat washers (#6), lock washers (#5) and
3/8" hex lock nuts (#4). Torque lock nuts (#4) to
31 ft. lbs.
6. Install the long skid shoes (#1) to the remaining three
deckcorners with 3/8”-16X11/4 GR5 plow bolts(#2), flat
washers (#6), lock washers (#5) and 3/8" hex lock nuts
(#4). Torque lock nuts (#4) to 31 ft. lbs.
7. Raise cutter up and remove support blocks.
Land Pride Standard Skid Shoe Bundle 326-027A
Item Part No. Part Description
1 312-602D SKID SHOE, 1/4" x 2"
2 326-276D DECK RUNNER LH REAR, 1/4" x 2"
3 802-466C PLOW 3/8-16X1 1/4 GR5
4 803-013C NUT LOCK 3/8-16 PLT
5 804-013C WASHER LOCK SPRING 3/8 PLT
6 804-012C WASHER FLAT 3/8 SAE PLT
Land Pride Heavy Skid Shoe Bundle 326-028A
Item Part No. Part Description
1 326-343D SKID SHOE HEAVY, 3/8" x 3"
2 326-344D SKID SHOE HEAVY SHORT, 3/8" x 3"
3 802-466C PLOW 3/8-16X1 1/4 GR5
4 803-013C NUT LOCK 3/8-16 PLT
5 804-013C WASHER LOCK SPRING 3/8 PLT
6 804-012C WASHER FLAT 3/8 SAE PLT
Skid Shoe Replacement
Figure 5-2
24546