Filter
Top Products
MODE
*Cycle Time,
Output 1B
*Rate,
Output 1B
*Derivative,
Output 1B
*Operation Prompt
*Proportional Band, Output 1B
*Reset,
Output 1B
*Integral,
Output 1B
Enter your settings,
from the controller's
upper display.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
Output 2 (p. 5.13)
Output 1 (p. 5.10)
*Cycle Time,
Output 2B
*Rate,
Output 2B
*Derivative,
Output 2B
*Proportional Band
,
Output 2B
*Reset,
Output 2B
*Integral,
Output 2B
*Dead Band B
MODE
[PIdb]
[OPer]
{Pb1b]
[RE1b]
[It1b]
[rA1b]
[de1b]
{CT1b}
[Pb2b]
[re2b]
[It2b}
[rA2b]
[dE2b]
[Ct2b]
[db`b]
WATLOW Series 988 User’s Manual 5.9
Operation Menus, Chapter 5
MODE
*Cycle Time,
Output 1
A
*Rate,
Output 1
A
*Derivative,
Output 1
A
Operation Prompt
Proportional Band, Output 1A
*Reset,
Output 1A
*Integral,
Output 1
A
Enter your settings,
from the controller's
upper display.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
Output 2 (p. 5.13)
Output 1 (p. 5.10)
*Cycle Time,
Output 2
A
*Rate,
Output 2
A
*Derivative,
Output 2
A
*Proportional Band, Output 2A
*Reset,
Output 2
A
*Integral,
Output 2
A
*Dead Band A
MODE
[PIDA]
[Oper]
[````]
[Pb1A]
[````]
[RE1A]
[````]
[It1A]
[````]
[rA1A]
[````]
[dE1A]
[````]
[Ct1A]
[````]
[Pb2A]
[````]
[Re2A]
[````]
[It2A]
[````]
[rA2A]
[````]
[dE2A]
[````]
[Ct2A]
[````]
[db`A]
System
Menu
p. 5.2
PID A
Menu
p. 5.9
PID B
Menu
p. 5.9
Set Point 2
MODE
MODE
Idle Set Point
[`988]
[`SP2]
[`988]
[IdSP]
[`SyS]
[PIdb]
[PIDA]
[OPEr]
[OPEr]
[OPEr]
❶ Begin in the Display Loop, and
press the Mode key µ to reach the
Set Point 2 prompt [`SP2], the Idle
Set Point prompt [IdSP] or the
System Menu [`SYS].
❷ Use Mode key µ to step past
the Set Point 2 prompt [`SP2] and
the Idle Set Point prompt [IdSP], if
they appear (see prompt informa-
tion). Upon reaching the Operation
Menu prompt [OPEr] use the Up-
arrow > key to select a menu.
Figure 5.9 -
The PID Menus.
❸ Press the Mode key µ to step
through the prompts.
❹ Press the Up-arrow key > to
step through the prompt values.
The Down-arrow key < backs
through the values.
…
…
…
[`)00]
[dE1A]
[`)01]
[dE1A]
[`)02]
[dE1A]
[`(99]
[dE1A]
*Prompts may not
appear, depending on
controller configuration.
Reaching the PID Menus
Operation-PID A or B
C5.wc 5/14/1999 8:51 AM Page 5.9