Filter
Top Products
28
Section 3 Adjustments
Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M 03/11/03
Land Pride
10. Jam both nuts against the block.
11. Push or pull on the deck lift foot pedal until the chain
on the left front just becomes tight, making sure that
the deck stays tight against the 3" block.
12. While keeping the chain tight, tighten the nuts against
the deck lift block on the height indicator rod. See
Figure 3-19.
13. Go to the right front of the mower.
14. Loosen the 5/16" jam nut on the adjuster lift chain
(Figure 3-18), and back the adjuster bolt out to allow
the adjuster to move up and down freely.
15. Be sure that adjuster is free to move up and down.
16. Tighten the adjuster bolt until the chain just becomes
tight, making sure that the deck stays tight against the
3" block.
17. Tighten the adjuster bolt jam nut to prevent the
adjuster bolt from moving. See Figure 3-18.
18. Tighten the hardware holding the chain and adjuster
onto the deck lift arm.
19. Go to the right rear of the mower.
20. Make sure that there is still slack in the chain. If not,
loosen the two nuts on the block holding the threaded
rod until there is slack in the deck lift chain.
See Figure 3-17.
21. Tighten the appropriate nut until the chain just
becomes tight, making sure that the deck stays tight
against the 3" block.
22. Tighten the othernut on theopposite sideof theblock,
and jam them tightly together against the block.
23. Go to the left rear of the mower.
24. Make sure that there is still slack in the chain. If not,
loosen the two nuts on the block holding the threaded
rod until there is slack in the deck lift chain.
See Figure 3-16.
25. Tighten the appropriate nut until the chain just
becomes tight.
26. Tighten the othernut on theopposite sideof theblock,
and jam them tightly together against the block.
27. Compress the deck lift assist springs so thatthere is 1”
of space between the front nut and on the spring and
the rear nut on thedeck lift block (Figure 3-20). Typical
both sides.
28. When completed, all chains will be tight, and deck
cutting height will be set to the deck height indicator.
Deck Cutting Height Adjustment
Deck height is adjustable from 1” to 5” in 1/4” increments.
The holes in the height adjusting bar are spaced at 1/2”
intervals. By turning theheight adjusting stop around, 1/4”
increments can be attained due to the 1/4” plate that is
part of the stop. Refer to Figure 3-21.
EXAMPLE: When the height adjusting stop is placed in
the 1” hole,with the1/4” platefacing tothe frontof the unit,
the cutting height is at 1”. When the height adjusting stop
is placed in the 1” hole, with the 1/4” plate on the
operator’s side of the hole, the cutting height is at 1 1/4”.
When the height adjusting stop is placed in one of the
holes, with the1/4” plateon theoperator’s sideof the hole,
the deck height will be set at one of the following: 1 1/4”,
1 3/4”, 2 1/4”, 2 3/4”, 3 1/4”, 3 3/4”, 4 1/4” or 4 3/4”.
When the height adjusting stop is placed in one of the
holes, with the 1/4” plate facing to the front of the unit, the
deck height will be set atone of the following: 1”, 1 1/2”, 2”,
2 1/2”, 3”, 3 1/2”, 4”, 4 1/2” or 5”.
The notch located at the rear of the right height adjusting
bar is to used when the deck is placed in the transport
mode.
Deck Cutting Height
Figure 3-21
19089
Height Adjusting
Stop
1/4”
Plate