Filter
Top Products
8
Introduction
RCS3596, RCSM3596, RCS3510 & RCSM3510 Series Rotary Cutters 312-708M
6/26/06
Land Pride
Table of Contents
Introduction
Owner Assistance
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Cutter.
The parts on your Cutter have been specially designed
and should only be replaced with genuine Land Pride
parts. Therefore, should your Cutter require replacement
parts go to your Land Pride Dealer.
Serial Number Plate
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer. Be sure to include your serial and model numbers in
correspondence also. Refer to Figure 1 for the location of
your serial number plate.
Further Assistance
Your dealer wants you to be satisfied with your new
Cutter. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
Serial Number Plate Location
Figure 1
20701
Land Pride welcomes you to the growing family of new
product owners.
This Cutter has been designed with care and built by
skilled workers using quality materials. Proper assembly,
maintenance, and safe operating practices will help you
get years of satisfactory use from the machine.
Application
The Land Pride RCS(M)3596 and RCS(M)3510 Series
Side Shift Rotary Cutters are designed and built to clear
grass, weeds, and light brush up to two inches in
diameter from areas under orchard and grove trees,
beneath over-hanging hedge rows, or under fence lines
and guard railings. Both units have 14" side shift
capability to either side of the tractor with rear mounted
360 degree rotating tailwheels. These cutters are also
well suited for operation on gentle slopes and mildly
contoured approaches immediately adjacent to ponds,
lakes, streams, drainage ditches, and roadways. The
eight or ten foot cutting width and 2" to 12" cutting height
make them well suited for mowing pastures, set aside
acres, and row crop fields.
The RCS3596 is adapted for Category 1 or 2 semi-hitch
mounting and 50 to 120 horsepower tractors. The Model
RCS3510 is approved for Category 2 or 3 semi-hitch
attachment and 60-120 horsepower tractors. Due to the
offset nature of the hitch, this cutter utilizes a
“semi-mount” hitch configuration. The top link will not be
used and the tailwheels will always be in contact with the
ground. Both models are available with either 540 rpm or
1000 rpm PTO capability and offer standard driveline
clutch protection. A stump jumper is standard equipment
and safety guards are available. See “Features and
Benefits”, “Section 5” for additional information.
Using This Manual
•
This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
www.landpride.com or printed from the Land Pride
Service & Support Center by your dealer.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
NOTE: A special point of information that the
operator must be aware of before continuing.