Filter
Top Products
624K Z-BAR AND HIGH-LIFT LOADERS WITH PIN-ON BUCKET
Z-Bar High-Lift
Dimensions with Bucket 2.7-m
3
(3.5 cu. yd.) general-purpose with bolt-on edge 2.7-m
3
(3.5 cu. yd.) general-purpose with bolt-on edge
A Height to Top of Cab and Canopy 3.32 m (10 ft. 11 in.) 3.32 m (10 ft. 11 in.)
B Hood Height 2.46 m (8 ft. 1 in.) 2.46 m (8 ft. 1 in.)
C Ground Clearance 384 mm (15.1 in.) 384 mm (15.1 in.)
D Length from Centerline to Front Axle 1.52 m (5 ft. 0 in.) 1.52 m (5 ft. 0 in.)
E Wheelbase 3.09 m (10 ft. 1 in.) 3.09 m (10 ft. 1 in.)
F Overall Length, Bucket on Ground 7.76 m (25 ft. 5 in.) 8.17 m (26 ft. 9 in.)
G Height to Hinge Pin, Fully Raised 3.95 m (13 ft. 0 in.) 4.30 m (14 ft. 2 in.)
H Dump Clearance, 45 deg., Full Height 2.86 m (9 ft. 5 in.) 3.23 m (10 ft. 7 in.)
I Reach, 45-deg. Dump, Full Height 1.02 m (3 ft. 4 in.) 1.11 m (3 ft. 8 in.)
J Reach, 45-deg. Dump, 2.13-m (7 ft. 0 in.) Clearance 1.57 m (5 ft. 2 in.) 1.93 m (6 ft. 4 in.)
K Maximum Digging Depth 95 mm (3.8 in.) 203 mm (8.0 in.)
L Maximum Rollback at Ground Level 37 deg. 36 deg.
M Maximum Rollback, Boom Fully Raised 50 deg. 49 deg.
N Maximum Bucket Dump Angle, Fully Raised 45 deg. 46 deg.
Loader Clearance Circle, Bucket Carry Position 12.24 m (40 ft. 2 in.) 12.61 m (41 ft. 4 in.)
SpeciƟcations with Bucket
Capacity, Heaped 2.7 m
3
(3.5 cu. yd.) 2.7 m
3
(3.5 cu. yd.)
Capacity, Struck 2.3 m
3
(3.0 cu. yd.) 2.3 m
3
(3.0 cu. yd.)
Bucket Weight with Bolt-On Cutting Edge 1148 kg (2,532 lb.) 1148 kg (2,532 lb.)
Bucket Width 2.69 m (8 ft. 10 in.) 2.69 m (8 ft. 10 in.)
Breakout Force 12 821 kg (28,266 lb.) 11 662 kg (25,709 lb.)
Tipping Load, Straight 13 822 kg (30,473 lb.) 11 604 kg (25,582 lb.)
Tipping Load, 40-deg. Full Turn 11 979 kg (26,409 lb.) 10 020 kg (22,090 lb.)
Rated Operating Load, 50% Full-Turn Tipping Load
(conforms to ISO 14397-1)*
5989.5 kg (13,206 lb.) 5010 kg (11,045 lb.)
Operating Weight 15 483 kg (34,134 lb.) 15 679 kg (34,566 lb.)
Loader operating information is based on machine with identiƟed linkage and standard equipment, PowerTech PVX 6068 (EPA Interim Tier 4/EU Stage IIIB) engine, ROPS
cab, rear cast bumper/counterweight, transmission side-frame guards, bottom guards, standard tires, full fuel tank, and 79-kg (175 lb.) operator. This information is
affected by changes in tires, ballast, and different attachments, and assumes no tire deƠection per the standard ISO 14397-1 section 5.
*Rated operating capacity based on Deere attachments only.
Hydraulic System/Steering (continued) 624K Z-BAR / HIGH-LIFT / POWERLLEL / TOOL CARRIER
Hydraulic Cycle Times Z-Bar High-Lift Powerllel Tool Carrier
Raise 5.9 sec. 5.9 sec. 5.9 sec. 5.6 sec.
Dump 1.3 sec. 1.3 sec. 1.4 sec. 3.0 sec.
Lower (Ơoat down) 2.7 sec. 2.7 sec. 2.8 sec. 2.7 sec.
Total 9.9 sec. 9.9 sec. 10.1 sec. 11.3 sec.
Dimensions and SpeciƟcations with Pin-On Bucket
N
E
H
M
K
IG
L
F
CD
A
Cab and
Canopy
B
J