Filter
Top Products
444K Z-BAR AND HIGH-LIFT LOADERS WITH PIN-ON BUCKET
Z-Bar High-Lift
Dimensions with Bucket 1.9-m
3
(2.5 cu. yd.) general-purpose with bolt-on edge 1.9-m
3
(2.5 cu. yd.) general-purpose with bolt-on edge
A Height to Top of Cab and Canopy 3.17 m (10 ft. 5 in.) 3.17 m (10 ft. 5 in.)
B Hood Height 2.19 m (7 ft. 2 in.) 2.19 m (7 ft. 2 in.)
C Ground Clearance 393 mm (15.5 in.) 393 mm (15.5 in.)
D Length from Centerline to Front Axle 1.37 m (4 ft. 6 in.) 1.37 m (4 ft. 6 in.)
E Wheelbase 2.76 m (9 ft. 1 in.) 2.76 m (9 ft. 1 in.)
F Overall Length, Bucket on Ground 6.86 m (22 ft. 6 in.) 7.20 m (23 ft. 7 in.)
G Height to Hinge Pin, Fully Raised 3.60 m (11 ft. 10 in.) 3.99 m (13 ft. 1 in.)
H Dump Clearance, 45 deg., Full Height 2.67 m (8 ft. 9 in.) 3.03 m (9 ft. 11 in.)
I Reach, 45-deg. Dump, Full Height 1.04 m (3 ft. 5 in.) 1.04 m (3 ft. 5 in.)
J Reach, 45-deg. Dump, 2.13-m (7 ft. 0 in.) Clearance 1.44 m (4 ft. 9 in.) 1.74 m (5 ft. 9 in.)
K Maximum Digging Depth 105 mm (4.1 in.) 105 mm (4.1 in.)
L Maximum Rollback at Ground Level 41 deg. 41 deg.
M Maximum Rollback, Boom Fully Raised 55 deg. 50 deg.
N Maximum Bucket Dump Angle, Fully Raised 50 deg. 45 deg.
Loader Clearance Circle, Bucket Carry Position 11.07 m (36 ft. 4 in.) 11.39 m (37 ft. 5 in.)
SpeciƟcations with Bucket
Capacity, Heaped 1.9 m
3
(2.5 cu. yd.) 1.9 m
3
(2.5 cu. yd.)
Capacity, Struck 1.6 m
3
(2.1 cu. yd.) 1.6 m
3
(2.1 cu. yd.)
Bucket Weight with Bolt-On Cutting Edge 870 kg (1,919 lb.) 870 kg (1,919 lb.)
Bucket Width 2.54 m (8 ft. 4 in.) 2.54 m (8 ft. 4 in.)
Breakout Force 7970 kg (17,570 lb.) 7356 kg (16,217 lb.)
Tipping Load, Straight 9233 kg (20,356 lb.) 7941 kg (17,507 lb.)
Tipping Load, 40-deg. Full Turn 8047 kg (17,741 lb.) 6897 kg (15,205 lb.)
Rated Operating Load, 50% Full-Turn Tipping Load
(conforms to ISO 14397-1)*
4024 kg (8,871 lb.) 3449 kg (7,603 lb.)
Operating Weight 11 203 kg (24,698 lb.) 11 362 kg (25,048 lb.)
Loader operating information is based on machine with identiƟed linkage and standard equipment, PowerTech PVX 4045 (EPA Interim Tier 4/EU Stage IIIB) engine, ROPS
cab, rear cast bumper/counterweight, transmission side-frame guards, bottom guards, standard tires, full fuel tank, and 79-kg (175 lb.) operator. This information is
affected by changes in tires, ballast, and different attachments, and assumes no tire deƠection per the standard ISO 14397-1 section 5.
*Rated operating capacity based on Deere attachments only.
Hydraulic System/Steering (continued) 444K Z-BAR / HIGH-LIFT / POWERLLEL
Hydraulic Cycle Times Z-Bar High-Lift Powerllel
Raise 5.9 sec. 5.9 sec. 5.3 sec.
Dump 1.0 sec. 1.0 sec. 1.1 sec.
Lower (Ơoat down) 2.4 sec. 2.4 sec. 1.9 sec.
Total 9.3 sec. 9.3 sec. 8.3 sec.
Dimensions and SpeciƟcations with Pin-On Bucket
N
E
H
M
K
IG
L
F
CD
A
Cab and
Canopy
B
J