Filter
Top Products
524K Z-BAR AND HIGH-LIFT LOADERS WITH PIN-ON BUCKET
Z-Bar High-Lift
Dimensions with Bucket 2.1-m
3
(2.75 cu. yd.) general-purpose with bolt-on edge 2.1-m
3
(2.75 cu. yd.) general-purpose with bolt-on edge
A Height to Top of Cab and Canopy 3.25 m (10 ft. 8 in.) 3.25 m (10 ft. 8 in.)
B Hood Height 2.30 m (7 ft. 7 in.) 2.30 m (7 ft. 7 in.)
C Ground Clearance 400 mm (15.7 in.) 400 mm (15.7 in.)
D Length from Centerline to Front Axle 1.45 m (4 ft. 9 in.) 1.45 m (4 ft. 9 in.)
E Wheelbase 2.93 m (9 ft. 7 in.) 2.93 m (9 ft. 7 in.)
F Overall Length, Bucket on Ground 7.34 m (24 ft. 1 in.) 7.67 m (25 ft. 2 in.)
G Height to Hinge Pin, Fully Raised 3.77 m (12 ft. 5 in.) 4.12 m (13 ft. 6 in.)
H Dump Clearance, 45 deg., Full Height 2.77 m (9 ft. 1 in.) 3.12 m (10 ft. 3 in.)
I Reach, 45-deg. Dump, Full Height 0.98 m (3 ft. 2 in.) 0.99 m (3 ft. 3 in.)
J Reach, 45-deg. Dump, 2.13-m (7 ft. 0 in.) Clearance 1.44 m (4 ft. 9 in.) 1.73 m (5 ft. 8 in.)
K Maximum Digging Depth 97 mm (3.8 in.) 222 mm (8.7 in.)
L Maximum Rollback at Ground Level 41 deg. 41 deg.
M Maximum Rollback, Boom Fully Raised 55 deg. 50 deg.
N Maximum Bucket Dump Angle, Fully Raised 51 deg. 47 deg.
Loader Clearance Circle, Bucket Carry Position 11.60 m (38 ft. 1 in.) 11.90 m (39 ft. 1 in.)
SpeciƟcations with Bucket
Capacity, Heaped 2.1 m
3
(2.75 cu. yd.) 2.1 m
3
(2.75 cu. yd.)
Capacity, Struck 1.7 m
3
(2.27 cu. yd.) 1.7 m
3
(2.27 cu. yd.)
Bucket Weight with Bolt-On Cutting Edge 991 kg (2,185 lb.) 991 kg (2,185 lb.)
Bucket Width 2.54 m (8 ft. 4 in.) 2.54 m (8 ft. 4 in.)
Breakout Force 9193 kg (20,267 lb.) 8504 kg (18,748 lb.)
Tipping Load, Straight 10 255 kg (22,609 lb.) 8803 kg (19,406 lb.)
Tipping Load, 40-deg. Full Turn 8914 kg (19,652 lb.) 7622 kg (16,804 lb.)
Rated Operating Load, 50% Full-Turn Tipping Load
(conforms to ISO 14397-1)*
4457 kg (9,826 lb.) 3811 kg (8,402 lb.)
Operating Weight 12 449 kg (27,445 lb.) 12 642 kg (27,871 lb.)
Loader operating information is based on machine with identiƟed linkage and standard equipment, PowerTech PVX 6068 (EPA Interim Tier 4/EU Stage IIIB) engine, ROPS
cab, rear cast bumper/counterweight, transmission side-frame guards, bottom guards, standard tires, full fuel tank, and 79-kg (175 lb.) operator. This information is
affected by changes in tires, ballast, and different attachments, and assumes no tire deƠection per the standard ISO 14397-1 section 5.
*Rated operating capacity based on Deere attachments only.
Hydraulic System/Steering (continued) 524K Z-BAR / HIGH-LIFT
Hydraulic Cycle Times Z-Bar High-Lift
Raise 6.1 sec. 6.1 sec.
Dump 1.4 sec. 1.4 sec.
Lower (Ơoat down) 3.0 sec. 3.0 sec.
Total 10.5 sec. 10.5 sec.
Dimensions and SpeciƟcations with Pin-On Bucket
N
E
H
M
K
IG
L
F
CD
A
Cab and
Canopy
B
J