Filter
Top Products
544K Z-BAR AND HIGH-LIFT LOADERS WITH PIN-ON BUCKET
Z-Bar Z-Bar High-Lift High-Lift
Dimensions with Bucket Narrow 2.3-m
3
(3.0 cu. yd.)
general-purpose with
bolt-on edge
Wide 2.3-m
3
(3.0 cu. yd.)
general-purpose with
bolt-on edge
Narrow 2.3-m
3
(3.0 cu. yd.)
general-purpose with
bolt-on edge
Wide 2.3-m
3
(3.0 cu. yd.)
general-purpose with
bolt-on edge
A Height to Top of Cab and Canopy 3.24 m (10 ft. 8 in.) 3.24 m (10 ft. 8 in.) 3.24 m (10 ft. 8 in.) 3.24 m (10 ft. 8 in.)
B Hood Height 2.30 m (7 ft. 7 in.) 2.30 m (7 ft. 7 in.) 2.30 m (7 ft. 7 in.) 2.30 m (7 ft. 7 in.)
C Ground Clearance 400 mm (15.7 in.) 400 mm (15.7 in.) 400 mm (15.7 in.) 400 mm (15.7 in.)
D Length from Centerline to Front Axle 1.45 m (4 ft. 9 in.) 1.45 m (4 ft. 9 in.) 1.45 m (4 ft. 9 in.) 1.45 m (4 ft. 9 in.)
E Wheelbase 2.93 m (9 ft. 7 in.) 2.93 m (9 ft. 7 in.) 2.93 m (9 ft. 7 in.) 2.93 m (9 ft. 7 in.)
F Overall Length, Bucket on Ground 7.43 m (24 ft. 4 in.) 7.34 m (24 ft. 1 in.) 7.75 m (25 ft. 5 in.) 7.67 m (25 ft. 2 in.)
G Height to Hinge Pin, Fully Raised 3.82 m (12 ft. 6 in.) 3.82 m (12 ft. 6 in.) 4.17 m (13 ft. 8 in.) 4.17 m (13 ft. 8 in.)
H Dump Clearance, 45 deg., Full Height 2.76 m (9 ft. 1 in.) 2.82 m (9 ft. 3 in.) 3.11 m (10 ft. 3 in.) 3.17 m (10 ft. 5 in.)
I Reach, 45-deg. Dump, Full Height 0.99 m (3 ft. 3 in.) 0.93 m (3 ft. 1 in.) 0.99 m (3 ft. 3 in.) 0.93 m (3 ft. 1 in.)
J Reach, 45-deg. Dump, 2.13-m (7 ft. 0 in.) Clearance 1.46 m (4 ft. 10 in.) 1.44 m (4 ft. 9 in.) 1.76 m (5 ft. 9 in.) 1.73 m (5 ft. 8 in.)
K Maximum Digging Depth 95 mm (3.72 in.) 95 mm (3.72 in.) 221 mm (8.7 in.) 221 mm (8.7 in.)
L Maximum Rollback at Ground Level 42 deg. 42 deg. 37 deg. 37 deg.
M Maximum Rollback, Boom Fully Raised 55 deg. 55 deg. 50 deg. 50 deg.
N Maximum Bucket Dump Angle, Fully Raised 49 deg. 49 deg. 46 deg. 46 deg.
Loader Clearance Circle, Bucket Carry Position 11.65 m (38 ft. 3 in.) 11.72 m (38 ft. 5 in.) 11.96 m (39 ft. 3 in.) 12.03 m (39 ft. 6 in.)
SpeciƟcations with Bucket
Capacity, Heaped 2.3 m
3
(3.0 cu. yd.) 2.3 m
3
(3.0 cu. yd.) 2.3 m
3
(3.0 cu. yd.) 2.3 m
3
(3.0 cu. yd.)
Capacity, Struck 2.0 m
3
(2.6 cu. yd.) 2.0 m
3
(2.6 cu. yd.) 2.0 m
3
(2.6 cu. yd.) 2.0 m
3
(2.6 cu. yd.)
Bucket Weight with Bolt-On Cutting Edge 1046 kg (2,305 lb.) 1029 kg (2,267 lb.) 1046 kg (2,305 lb.) 1029 kg (2,267 lb.)
Bucket Width 2.54 m (8 ft. 4 in.) 2.69 m (8 ft. 10 in.) 2.54 m (8 ft. 4 in.) 2.69 m (8 ft. 10 in.)
Breakout Force 10 110 kg (22,289 lb.) 10 864 kg (23,951 lb.) 9347 kg (20,606 lb.) 10 044 kg (22,144 lb.)
Tipping Load, Straight 10 878 kg (23,983 lb.) 10 935 kg (24,107 lb.) 9391 kg (20,703 lb.) 9447 kg (20,828 lb.)
Tipping Load, 40-deg. Full Turn 9428 kg (20,784 lb.) 9479 kg (20,898 lb.) 8111 kg (17,881 lb.) 8162 kg (17,995 lb.)
Rated Operating Load, 50% Full-Turn Tipping Load
(conforms to ISO 14397-1)*
4714 kg (10,392.6 lb.) 4740 kg (10,449 lb.) 4056 kg (8,941 lb.) 4081 kg (8,997 lb.)
Operating Weight 13 000 kg (28,660 lb.) 12 982 kg (28,621 lb.) 13 158 kg (29,009 lb.) 13 141 kg (28,970 lb.)
Loader operating information is based on machine with identiƟed linkage and standard equipment, PowerTech PVX 6068 (EPA Interim Tier 4/EU Stage IIIB) engine, ROPS
cab, rear cast bumper/counterweight, transmission side-frame guards, bottom guards, standard tires, full fuel tank, and 79-kg (175 lb.) operator. This information is
affected by changes in tires, ballast, and different attachments, and assumes no tire deƠection per the standard ISO 14397-1 section 5.
*Rated operating capacity based on Deere attachments only.
Hydraulic System/Steering (continued) 544K Z-BAR / HIGH-LIFT / POWERLLEL
Hydraulic Cycle Times Z-Bar High-Lift Powerllel
Raise 5.8 sec. 5.8 sec. 5.8 sec.
Dump 1.2 sec. 1.2 sec. 1.2 sec.
Lower (Ơoat down) 3.2 sec. 3.2 sec. 2.5 sec.
Total 10.2 sec. 10.2 sec. 9.5 sec.
Dimensions and SpeciƟcations with Pin-On Bucket
N
E
H
M
K
IG
L
F
CD
A
Cab and
Canopy
B
J