Filter
Top Products
14
ure 5). You may also need to adjust the
Deck Links (See Figure 5).
d. Lower the mower deck to the cutting posi-
tion. With a wrench loosen the inner rear
nut on the Deck Lift Spring Assist. To
adjust the deck up or down, use a wrench
and with a few turns, adjust clockwise or
counter clockwise the outer rear nut of the
Deck Lift Spring Assist. Repeat this proce
-
dure on the opposite side of the Mower.
Once the deck is adjusted, retighten bolts.
e. With the deck still in the cutting position,
adjust the Deck Links. With a wrench
loosen the top inner bolt of the Deck Link.
To adjust the side of the deck up or down
turn the top bolt clockwise or counter
clockwise a few turns. Adjust both front
and rear Deck links as necessary.
Retighten nuts.
f. Raise the mowing deck to the transport
position using the upper foot pedal.
g. Use the second foot pedal to lower the
mowing deck to the cutting position and
repeat step “b.” above to make sure that
the desired cutting height has been
attained. If the dimensions are not correct,
repeat steps “c.” through “f.” above.
5. Lubricate all fittings listed in the mainte-
nance section.
D. Zero Turn Break-In And Operating
Procedures
DANGER:
Reread the “When Mowing” Safety Precautions.
The following procedures are suggested for opera-
tors of ride-on machines which have zero turn
capabilities.
1. Orientation:
a. Read the entire Operator’s Manual.
b. Sit on the machine, adjust the seat before-
and-after, then adjust the speed/directional
(lap bar) controls (they can be adjusted
fore-and-aft, as well as up-and-down —
9/16" wrench required).
c. Become familiar with all of the machine
controls, instrumentation, safety and
instruction signs, and safety devices.
d. Move (or have moved) the machine to a
safe, level area with no obstructions includ
-
ing objects, pedestrians, and animals.
2. Initial Operation:
a. Use protective equipment for eyes, hands,
hearing, feet, legs, head and other areas of
the body if needed — safety eye glasses,
gloves, earplugs, boots, hats, etc.
WARNING:
Hearing Protection is required for all operator
exposure exceeding two (2) hours.
b. Ensure that the area is free of animals and
bystanders, especially children!
c. Survey the area where the equipment is to
be used to make sure it is free of debris,
sticks, stones, wires, bones, and other for
-
eign objects which could cause injury to
bystanders, damage to the machine, or
damage to nearby facilities.
d. Inspect the machine to make sure:
1. All guards, shields (including mower
chute deflector) are in their proper place,
are secure, and are functional.
2. That there are no spilled or leaking fuel
or oil sources, nor loose fuel or hydraulic
tank caps, hoses or fittings.
3. That there are no loose or missing hard-
ware nor any missing items.
4. That no non-approved devices are
installed.
5. That all safety signs and decals are
properly installed and legible.
e. This is a one person machine, operator
only! Riders are not permitted under any
circumstance!
f. To start the engine on the machine:
1. Make sure the park brake is set to the
“ON” position, both lap bars are in the
neutral/start position, and the Power
Take Off (PTO also referred to as blade
control switch) is in the “off” (down) posi
-
tion.
2. Move the choke control forward and the
engine speed control (throttle) forward
(half way).
Note: E.F.I. Tanks do not have a choke control.
3. Insert the ignition key, turn the switch
toward the spring-loaded “Start” position,
maintain the Start position until the
engine begins to run, then release the
Deck Links
Deck Lift Spring inner nut
Figure. 5