Filter
Top Products
12
wheel, making the mower turn toward the side
where the lever is behind. When one lever is
pushed forward and the other lever pulled back
the same amount, one traction wheel will turn in
reverse and the mower will turn within its own
length.
In order to start the engine, both steering levers
must be in the neutral position; the parking brake
must be engaged; and the blade clutch switch
must be “off”. However, once the engine starts,
the parking brake must be released before the
operator places the steering levers into the
operating position or the engine will
automatically shut off.
Note: The Steering Lever will return toward
neutral when released, but they should be placed
in neutral by the driver. If the Drive Handles are
not placed in neutral, the tractor may creep.
4.
Electric Blade Clutch Switch:
(See Figure 1.)
Located on the right side of the mower beside the
ignition switch. This is an “on/off” push pull switch
that controls the electric blade clutch which sup
-
plies power to the cutting blades through the
PTO. The switch must be turned off to start the
engine and should be turned off for safety any
time another person approaches the mower or
the mowing deck is raised to the transport posi
-
tion. Power to the electric clutch will also be cut
off if the operator leaves the operator’s seat.
5.
Parking Brake:
(See Figure 2.) Located on the
left side of the traction unit. The handle is an
overcenter lever which applies the drum-type
brake on each drive wheel when the handle is
pulled to the rear. The brake must be engaged in
order to start the engine.
6.
Foot Pedal Lift:
(See Figure 3.) Located on the
right front corner of the mowing deck. A two pedal
mechanism is provided whereby one pedal (first)
is used to raise, to momentarily hold the imple
-
ment at a desired height (if needed), and to latch
it in the transport or maximum height setting. A
second pedal is used to unlatch the mechanism
from the transport or maximum height setting, to
lower, or to momentarily hold the implement at a
desired height. The pedals can also be used in
conjunction with each other when the upper por
-
tion of a foot activates the first pedal to raise the
implement, and the lower portion of the foot
(heel) activates the second pedal to release the
latch. This provides a hands-free operation with
the exception of when an implement height
change is required. For changing implement
height, at least one hand is required to reposition
the pins to provide 1/4” height-of-cut increments.
The mechanism includes: An adjustable location
foot pedal that is used to raise the implement
and/or latch it in the transport position, that is
directly connected to the implement lift linkage;
adjustable force counter-balance springs to
reduce the effective weight of the implement and
thereby reducing the forces needed on the first
and second pedals for activation - tighten both
springs equally to reduce the force at the foot
pedal; a second pedal pivotally attached to the
first pedal that releases the mechanism from the
latched configuration; a height adjustment link
and index provide predetermined height for the
implement - it is settable in 1/4” increments; a
lock position for the height adjustment link setta
-
ble by the pin in the highest (also transport posi-
tion) or lowest (also for mower deck removal and
installation).
The following features are incorporated into the
foot pedal implement lift design: Foot actuated
implement lift with one pedal (1st) for lift and
latch, with a second pedal for release and lower;
allows for some operators with physical limita
-
tions to use the implement lift mechanisms and
the machine; reduces potential for operator
fatigue; accommodates a variety of operator
sizes, shapes, and strengths; does not require
the use of hands (with the exception of resetting
the implement height) during normal machine
operation - thusly the hands can be used for other
functions
7.
Fuel Shutoff Valve:
(See Figure 4.) Located on
top of the fuel tank(s). When turned in a clockwise
Steering Levers
Foot Pedal Lift
Figure. 3
Fuel Shutoff Valve
Figure. 4
Note: The 19hp
and 23hp use the 5
gallon fuel tank.