Filter
Top Products
26
PROBLEM CAUSE CORRECTION
Engine continues to
run when operator
leaves seat with atta-
chment clutch engaged
1 Faulty operator-safety presence
control system.
1 Check wiring, switches and
connections. If not corrected,
contact a qualified service center.
Poor cut - uneven
cutting
1 Worn, bent or loose blade. 1 Replace blade. Tighten blade bolt.
2 Mower deck not level. 2 Level mower deck.
3 Buildup of grass, leaves, and trash
under mower.
3 Clean underside of mower
housing.
4 Bent blade mandrel. 4 Contact a qualified service center.
5 Clogged mower deck vent from
build-up of grass, leaves, and
trash around mandrel.
5 Clean around mandrels to
open vent holes.
Mower blade will
not rotate
1 Obstruction in clutch mechanism. 1 Remove obstruction.
2 Worn/damaged mower drive belt. 2 Replace mower drive belt.
3 Frozen idler pulley. 3 Replace idler pulley.
4 Frozen blade mandrel. 4 Contact a qualified service center.
Poor grass
discharge
1 Travel speed too fast. 1 Shift to slower speed.
2 Wet grass. 2 Allow grass to dry before mowing.
3 Mower deck not level. 3 Level mower deck.
4 Low/uneven tire air pressure. 4 Check tires for proper PSI.
5 Worn, bent or loose blade. 5 Replace/sharpen blade. Tighten
blade bolt.
6 Buildup of grass, leaves and
trash under mower.
6 Clean underside of mower
housing.
7 Mower drive belt worn. 7 Replace mower drive belt.
8 Blade improperly installed. 8 Reinstall blade sharp edge down.
9 Improper blade used. 9 Replace with blade listed in
this manual.
10 Clogged mower deck vent holes
from buildup of grass, leaves, and
trash around mandrels.
10 Clean around mandrels to
open vent holes.
Battery will not
charge
1 Bad battery cell(s). 1 Replace battery.
2 Poor cable connections. 2 Check/clean all connections.
3 Faulty alternator. 3 Replace alternator.
Loss of drive
1 Freewheel control in
“DISENGAGED” position.
1 Place freewheel control in
“ENGAGED” position.
2 Axle key missing. 2 Install axle key at rear wheel. See
"TO REMOVE WHEEL" in the
Service and Adjustments section.
Engine dies when
tractor is shifted
into reverse
1 Reverse operation system (ROS)
is not “ON” while mower or other
attachment is engaged.
1 Turn ignition key to ROS “ON”
position. See Operation section.
TROUBLESHOOTING CHART:
15
MOWING TIPS
• Mower should be properly leveled for best
mowing performance. See “TO LEVEL
MOWER HOUSING” in the Service and
Adjustments section of this manual.
• The left hand side of mower should be
used for trim ming.
• Drive so that clippings are dis charged onto
the area that has already been cut. Have
the cut area to the right of the riding mower.
This will result in a more even dis tri bu tion
of clippings and more uniform cutting.
• When mowing large areas, start by turning
to the right so that clippings will discharge
away from shrubs, fences, driveways,
etc. After one or two rounds, mow in the
opposite direction making left hand turns
until finished.
• If grass is extremely tall, it should be
mowed twice to reduce load and possible
fire hazard from dried clip pings. Make
first cut relatively high; the second to the
desired height.
RECOIL STARTING SYSTEM
This unit is equipped with an engine recoil
starting system. If the battery is too weak
to start engine.
1. Set parking Brake.
2. Turn key to ON position.
3. Make sure unit is in neutral position.
4. Set deck to disengaged position.
5. Pull recoil cord to start engine.
Recoil Starter
Handle
Gasoline Filler
Cap
• Do not mow grass when it is wet. Wet
grass will plug mower and leave undesir-
able clumps. Allow grass to dry before
mowing.
• Reg u late ground speed by se lect ing a low
enough gear to give the mower cut ting
per for mance as well as the quality of cut
desired.
• When operating attachments, se lect a
ground speed that will suit the terrain and
give best performance of the at tach ment
being used.