Filter
Top Products
20
MAINTENANCE
MUFFLER
Inspect and replace corroded muffler and spark ar-
rester (if equipped) as it could create a fire hazard
and/or damage.
SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, which-
ever occurs first. Spark plug type and gap setting are
shown in “PROD UCT SPECIFICATIONS” section of
this manual.
IN-LINE FUEL FILTER (See Fig. 26)
The fuel filter should be replaced once each season.
If fuel filter becomes clogged, ob struct ing fuel flow to
car bu re tor, re place ment is re quired.
• With engine cool, remove filter and plug fuel line
sec tions.
• Place new fuel filter in position in fuel line with
arrow pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.
CLAMP
FUEL FILTER
CLAMP
FIG. 26
CLEANING
• Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gaso-
line, oil, etc.
• Protect painted surfaces with automotive type
wax.
We do not recommend using a garden hose or pres-
sure washer to clean your tractor unless the engine
and transmission are covered to keep water out. Water
in engine or transmission will shorten the useful life
of your tractor. Use compressed air or a leaf blower
to remove grass, leaves and trash from tractor and
mower.
ENGINE OIL FILTER
Replace the engine oil filter every season or every
other oil change if the tractor is used more than 100
hours in one year.
CLEAN AIR SCREEN
Air screen must be kept free of dirt and chaff to prevent
engine dam age from overheating. Clean with a wire
brush or compressed air to re move dirt and stubborn
dried gum fibers.
AIR FILTER
Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions.
See Engine Manual.
DECK WASHOUT PORT (See Fig. 27)
Your tractor’s deck is equipped with a washout port on
its surface as part of its deck wash system. It should be
utilized after each use.
1. Drive the tractor to a level, clear spot on your lawn, near
enough to a water spigot for your garden hose to reach.
IMPORTANT: Make certain the tractor’s discharge chute is
directed AWAY from your house, garage, parked cars, etc.
Remove bagger chute or mulch cover if attached.
2. Make sure the PTO (Blade Engage) is not engaged,
set the parking brake, and stop the engine.
3. Thread the nozzle adapter (packaged with your tractor’s
Operator’s Manual) onto the end of your garden hose.
4. Pull back the lock collar of the nozzle adapter and push
the adapter onto the deck washout port at the left end
of the mower deck. Release the lock collar to lock the
adapter on the nozzle.
WASHOUT
PORT
NOZZLE ADAPTER
HOSE
IMPORTANT: Tug hose ensuring connection is secure.
5. Turn the water on.
6. While sitting in the operator’s position on the tractor,
re-start the engine and place the throttle lever in the
Fast "
" position.
IMPORTANT: Recheck the area making certain the area
is clear.
7. Move the tractor’s PTO (Blade Engage) to the ON
position. Remain in the operator’s position with the
cutting deck engaged until the deck is cleaned.
8. Move the tractor’s PTO (Blade Engage) to the OFF
position. Turn the ignition key to the STOP position to
turn the tractor’s engine off. Turn the water off.
9. Pull back the lock collar of the nozzle adapter to dis-
connect the adapter from the nozzle washout port.
10. Move the tractor to a dry area, preferably a concrete or
paved area. Engage the mower deck PTO to remove ex-
cess water and to help dry before putting the tractor away.
WARNING: A broken or missing washout
fitting could expose you or others to
thrown objects from contact with the blade.
• Replace broken or missing washout fitting
immediately, prior to using mower again.
• Plug any holes in mower with bolts and locknuts.
Fig. 27