Filter
Top Products
8
A.
GRIP SAW FIRMLY: Hold the chain saw firmly with
both hands when the motor is running. Keep a
good firm grip on the saw with both hands, the right
hand on the rear handle, and the left hand on the
front handle.
B. Do not over reach.
C.
Keep proper footing and balance at all times.
D. Do not let the nose of the guide bar contact a log,
branch, ground or other obstruction.
E. Do not cut above shoulder height.
F. Use devices, such as low-kickback chain, guide bar
nose guards, chain brakes and special guide bars,
which reduce the risks associated with kickback.
G. Use only replacement bars and chains specified by
the manufacturer or the equivalent.
H. There are no other replacement components for
achieving kickback protection in accordance with
CSA Z62.3.
20.POWER SUPPLY: Connect the chain saw to correct
voltage; be sure that the voltage supplied is the same
as that specified on the nameplate of the tool.
21.DO NOT operate a chain saw that is damaged,
improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the trigger is released.
22.DO NOT attempt operations beyond your capacity or
experience.
23.DO NOT operate a chain saw with one hand! Serious
injury to the operator, helpers, or bystanders may
result from one-handed operation. A chain saw is
intended for two-handed use.
24.TO REDUCE potential for electric shock, do not oper-
ate the saw on wet or slippery surfaces, or during
snow storms, rain storms, and other adverse weather
conditions.
25.DO NOT allow dirt, debris or sawdust to build up on
the motor or outside air vents.
26.Follow the manufacturer’s sharpening and mainte-
nance instructions for the saw chain.
27.Cut at high motor speeds.
28.Operation of a chain saw should be restricted to
mature, properly instructed individuals.
29.Your chain saw is intended for occasional homeowner
use. It is not made for heavy continuous use.
30.DO NOT FORCE a small saw to do a job requiring a
heavier duty unit.
31.EXAMINE
THE ELECTRICAL SWITCHES. Do not use
the chain saw if the switches do not properly turn on and
off. Do not attempt to make any repairs to the electric
switches. Take your saw to a MTD Authorized Service
Center
.
32.MAINTAIN EXTENSION CORDS. Inspect the exten-
sion cords periodically and replace if damaged. Only
use power cords that are suitably marked for outdoor
use.
33.DO NOT OPERATE YOUR CHAIN SAW near or
around flammable liquids or gases, whether in or out
of doors. An explosion and/or fire may result.
34.This electric powered saw is classified by CSA as a
Class 2C saw. It is intended for infrequent use by
homeowner’s, cottagers and campers, and for such
general applications such as clearing, pruning, cutting
firewood, etc. It is not intended for prolonged use. If
the intended use involves prolonged periods of opera-
tion, this may cause circulatory problems in the user’s
hands due to vibration. It may be appropriate to use a
saw having an anti-vibration feature.
35.NEVER REMOVE, modify or make inoperative any
safety device furnished with your unit.
36.Safety clothing required by your safety organizations,
government regulations, or your employer should be
used; otherwise, snug fitting clothing, safety footwear,
and hand and ear protection should be worn.
37.When felling, keep at least 2 tree lengths between
yourself and your fellow workers.
38.All chain saw service, other than the items listed in the
user manual safety and maintenance instructions,
should be performed by competent chain saw person-
nel. Do not attempt to repair it yourself; there are no
user serviceable parts inside.
NOTE:
Low-kickback saw chain is chain that has met the
kickback performance requirements of ANSI B175.1-1991
and is in accordance with CSA Z62.3. Do not use other
replacement chain unless it has met these requirements for
your specific model.
DO NOT USE ANY OTHER CUTTING ATTACH-
MENT OR ACCESSORIES. Use only MTD
replacement parts and accessories, which are designed
specifically to enhance the performance and maximize
the safe operation of our products. Failure to do so may
cause poor performance and possible injury. Use only
the chain and bar supplied with this product. Do not use
any other cutting attachment. Use of such attachments
will void your factory warranty and could result in serious
bodily injury.
39.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
1.Double insulated - No Serviceable Parts Inside.
2.To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider then the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any
way.
3.With a basic understanding of kickback, you can
reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
4.KEEP THE WORK AREA CLEAN: Cluttered areas
invite injuries. Do not start cutting until you have a
clear work area, secure footing, and a planned retreat
path from the falling tree.
5.GUARD AGAINST ELECTRIC SHOCK: Prevent body
contact with grounded surfaces (i.e., metal pipes, wire
fences).
6.CONSIDER THE WORK AREA ENVIRONMENT: Use
extreme caution when cutting small sized brush and
sapling, as slender material may catch the saw chain
and be whipped toward you or pull you off balance. Do
not operate a chain saw in a tree unless you are specif-
ically trained to do so. When cutting a limb that is under
tension, be alert for spring back so that you will not be
struck when the tension in the wood fibers is released.
Do not expose the chain saw to rain. Do not use the
chain saw in damp or wet locations. Do not use the
chain saw in the presence of flammable liquids or
gases.
7.KEEP CHILDREN AND BYSTANDERS AWAY: Do not
let visitors contact the chain saw or extension cord. All
visitors should be kept away from the work area.
8.STORE THE IDLE CHAIN SAW: When not in use, chain
saws should be stored out of the reach of children, in a
dry, high or locked-up place. When storing saw, use a
scabbard or carrying case.
9.DO NOT FORCE THE CHAIN SAW: The chain saw will
do a better and safer job when used at the rate for which
it was intended.
10.USE THE RIGHT TOOL: Cut wood only. Do not use the
chain saw for purposes for which it was not intended.
For example, do not use the chain saw for cutting plas-
tic, masonry, or non-building materials.
11.DRESS PROPERLY: Do not wear loose clothing or jew-
elry, as they can get caught in moving parts. Non-skid
footwear is recommended when working outdoors.
Wear protective hair covering to contain long hair.
12.USE SAFETY GEAR: Use safety glasses, safety
footwear, snug fitting clothing, protective gloves, and
protective hearing and head gear
.
13.STAY ALERT: Watch what you are doing. Use common
sense. Do not operate the chain saw when you are tired.
Keep all parts of your body away from the saw chain
when the motor is operating. Before you start the saw,
make sure the saw chain is not contacting anything.
14.MAINTAIN THE CHAIN SAW WITH CARE: Inspect the
chain saw cords periodically and, if damaged, have
them repaired by an authorized service facility. Keep the
cord clear of the chain and operator at all times. Never
carry the saw by the cord or pull it to disconnect from
receptacle. Keep the cord from oil and sharp edges.
Inspect the extension cords periodically and replace if
damaged. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating
and changing accessories. Keep handles dry, clean and
free from oil and grease.
15.DISCONNECT THE CHAIN SAW: Disconnect the chain
saw when not in use, before servicing, and when chang-
ing accessories and attachments such as saw chain and
guard.
16.OUTDOOR EXTENSION CORDS: Use only extension
cords that are intended for outdoor use and which are so
marked.
17.CHECK DAMAGED PARTS: Before further use of the
chain saw, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by an
authorized service center, unless otherwise indicated in
this instruction manual.
18.CARRYING THE SAW: Carry the saw by the front han-
dle with the saw stopped. Keep your finger off the
switch, and make sure that the guide bar and saw chain
are to the rear.
19.GUARD AGAINST KICKBACK:
When using an electric
chain saw
, basic safety
precautions should
always be followed to reduce the risk of fire,
electric shock, and injury to persons, including
the following:
WARNING:
Kickback may occur
when the nose or tip of
the guide bar touches an object, or when the
wood closes in and pinches the saw chain in
the cut. Tip contact in some cases may cause a
lightning-fast reverse action, kicking the guide
bar rapidly back towards the operator. Pinching
the saw chain along the top of the guide bar
may push the guide bar rapidly back towards
the operator. Either of these reactions may
cause you to lose control of the saw, which
could result in serious injury to the user. The fol-
lowing precautions should be followed to mini-
mize kickback.
WARNING:
7