Land Pride RCM6010 Brush Cutter User Manual


 
39
Section 7: Features and Benefits
8/28/08
RC5010 & RC6010 (540 RPM) and RCM5010 & RCM6010 (1000 RPM) Rotary Cutters 318-128M
Land Pride
Table of Contents
Section 7: Features and Benefits
RC5010 & RCM5010 Series
Features Benefits
250 HP Splitter box Tough gearbox to handle heavy-duty work.
210 HP wing boxes Tough gearbox to handle heavy-duty work.
Tractor HP range 50 - 250 HP
Gearbox warranty S/N 325492+ 5 years on housing, gears and shafts, 3 years on seals & bearings.
2 3/8” Output shaft Large output shaft handles shock loads better.
Input driveline: Cat. 5 Constant velocity or conventional u-joint available.
540 or 1000 RPM Fits wide variety of tractors.
Self-leveling clevis type hitch Reduces drawbar wear by keeping hitch level while going through ditches.
Double swivel hitch (Optional) Great for uneven terrain, reduces drawbar wear.
Bar-tite hitch (Optional) Ideal drawbar for extreme conditions. Clamps tight to the drawbar eliminating any drawbar
wear
Gearbox seal protection Gearbox bottom seal is protected for longer bearing life.
10 Gauge deck Heavy deck design holds up to harsh conditions.
1/4 ” Sidewall thickness Reduces debris piercing possibilities.
10 1/2” Deck height Handles heavy cutting, which reduces balling up of cut material under the deck.
2” to 14” Cutting Height Cover a wide range of cutting conditions.
6” Blade overlap Eliminates skipping during turns.
3” Cutting capacity Can cut brushy areas with saplings.
High blade tip speed (540 rpm = 14,909 fpm center & 15,037 fpm wing)
(1000 rpm = 15,606 fpm center & 14,651 fpm wing)
Allows clean cutting of material.
Replaceable skid shoes Can be replaced when damaged or worn out on wing and center deck.
3/16” Stump jumper Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough
conditions.
Deck rings (option) Keeps blades from damaging the deck.
4 Plate slip-clutch Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
Easy to Grease drivelines Drivelines have access holes to grease the U-joints of the driveline, as well as holes to
grease the inner profiles.
Hinged wing section Allow you to shape the cutter to the job. Ideal for rough ground where hillsides, ditches and
hollows can cause uneven cutting.
1” Solid hinge rods Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the
hinge area itself.
Transport wing locks Transport wing lock securely holds the wing in the folded position in case of hydraulic
failure.
Enclosed front to rear dual
leveling rods
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough
terrain. Some competitors only use one leveling rod.
Airplane tire option
with optional foam sealant
Airplane tires give better cushion while transporting the cutter. Available with heavy-duty
foam which virtually eliminates flats.
Laminated tires option Can’t go flat.
Replaceable wheel spindles Wheel spindles can be replaced easily by removing two bolts vs. replacing the entire axle.
Wheels 5 or 6 Wheel option.
Spring cushioned center-axle Protects unit from bumps and ground shock.
Walking Tandem (Optional) Better flotation on rougher terrain.
Surpassed rugged industry
standards
All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing
procedures specified by ANSI.
Paint Options Choice of red, green or tan to match popular tractor lines.