Filter
Top Products
ENGLISH
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive
liquid detergent solution. You can protect and restore
the gloss to a dulled acrylic surface by applying
Meguiar's #10 Mirror Glaze, a product specifically de-
signed for use on acrylic finishes. If Meguiar's is not
available, an acrylic polish of equal quality or automo-
tive paste wax is acceptable.
Never use abrasive household cleaners on any
Jacuzzi Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color fin-
ish can be removed by lightly sanding with 600-grit wet/
dry sandpaper. Restore the gloss using Meguiar's Mir-
ror Glaze or automotive paste wax.
Major scratches and gouges which penetrate the
acrylic surface will require refinishing. Ask your Jacuzzi
Whirlpool Bath dealer for special instructions.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE
PURGED AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the
whirlpool system, it is recommended that a whirlpool
bath be purged at least twice a month. For best results,
however, we recommend that you purge your whirlpool
bath after each use using our exclusive two-part plum-
bing system cleaner made specifically for whirlpool
baths. Systems Clean ™ is available through an autho-
rized Jacuzzi Whirlpool Bath Distributor or by calling us
direct at 1-800-288-4002. Instructions for use: Imme-
diately after bathing and exiting the whirlpool bath, leave
the bath water in the tub and add hot water, if necessary,
so the water is at least 1" (25 mm) above the highest jet.
Turn on the unit without the aerator. Pour the contents
of the Systems Clean Packet 1 (taking care not to get the
material on yourself) into the bath near the intake for the
circulation pump. Repeat same process with Systems
Clean Packet 2. It is important to use Packet 1 before
Packet 2 to avoid a strong odor. Run the bath for 5 to
10 minutes. Drain completely and rinse any residue.
If you have followed the standard purging instructions
above and still have an excess accumulation of bath
residue and desire an alternative cleaning mechanism,
we recommend SUPER SYSTEMS CLEAN PLUS manu-
factured by Stearns Packaging to rectify this condition.
This may be obtained by contacting us at l-800-288-
4002. It is recommended that you follow the instructions
provided by the manufacturer with the product. Re-
peated use may be necessary. SUPER SYSTEMS
CLEAN PLUS does not replace the necessity to regu-
larly purge your whirlpool system with Systems Clean as
recommended.
(For additional information about water content, contact
us for a copy of the Jacuzzi Water Quality Primer.)
Lamp
An optional lamp kit is available from your Jacuzzi
Whirlpool Bath dealer for installation on your bath.
When the bulb burns out, replace it from the back of
the lamp fitting, on the underside of the shell, by pulling
out the bulb receptacle. Replacement bulbs (12V, 7W)
are available from your Jacuzzi Whirlpool Bath dealer.
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH
ADDITIVES.
If you want to use any kind of bath additive, use only a
small amount of low-foaming powder or crystal sub-
stance; the whirlpool action intensifies the foaming prop-
erties of soaps.
The use of certain bath oils, bubble baths and bath
additives may increase the level of accumulations of
bath residue in the whirlpool system. If excess accumu-
lations persist, you should discontinue use of these
products.
Suction Cover/Strainer Maintenance
Clean the suction cover/strainer of hair and debris
when necessary. To do this, remove the center screw
and detach the square cover. Clean the cover by back-
flushing debris from the holes. Replace the suction cover
immediately after cleaning. When reinstalling, orient
the cover/strainer with the small notch at the bottom.
The gasket must be inserted into the groove of the cover/
strainer before reinstalling onto the suction fitting.
CAUTION: Keep hair a minimum of 6" (15 cm) inches
away from the suction fitting at all times when the
whirlpool system is operating. Hair longer than
shoulder length should be secured close to the head,
or a bathing cap should be worn. Do not operate
the whirlpool system with the suction cover re-
moved! It is a safety device and must always be in
place on the suction fitting to minimize the poten-
tial hazard of hair and body entrapment.
NOTCH
GASKET
COVER STRAINER
SCREW
SUCTION
FITTING
SUCTION COVER/STRAINER ASSEMBLY
MAINTENANCE
LIGHT BULB REPLACEMENT
LIGHT BULB
LIGHT BEZEL
BATH SHELL
BULB RECEPTACLE
LOCKING NUT
11
Jacuzzi Whirlpool Bath© U961000G 2/05