Casablanca Fan Company 63XXT Outdoor Ceiling Fan User Manual


  Open as PDF
of 11
 
8
Inteli•Touch
®
R
R
R
ProgrammedintoeveryInteli-TouchSeriesfanisanAutomatic
Demonstration Program. It can be used to fully demonstrate and
test the operation of the fan.
To enter the demonstration program:
1. Turn POWER off for at least three seconds. This will clear
the fan memory ready for programming.
2. Turn POWER on.
3. Immediately operate the buttons in the following sequence:
Amulti-tonesignalwillverifythestartofthetestprogramwhich
proceeds as follows:
• Lightsslowlyincreasetofullintensity.
• Fanacceleratestospeedthreewithaudiotones.
• Lightdimstohalfintensity.
• Fanacceleratestofullspeedwithaudiotones.
• Fanreversesatfullspeedwithaudiotones.
• Fanoperatesatfullspeed.
• Fanpowerisreversedwithaudiotones.
• Fanturnsoffwithaudiotones(bladescoastforashorttime).
• Lightsturnoff.
Thecompletecyclelastsslightlyoveroneminute.Itwillcontinue
to repeat until the POWER is turned off for more than three
seconds, cancelling the program.
The POWER button is normally left in the on position. Always turn the
poweroffduringcleaningorservicingthefanandduringthunderstorms.It
isalsousedtoexitorenteradditionalprograms.
POWER must be left on to retain a previously set fan speed or light
level.
Therearesixindividualspeedsettingsforthefan;eachspeedisindicated
by an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled . The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the buttonisused.Tomaintainthislevelofspeed,
turn the fan on by pressing less than one second. To lower speed,
turn fan off, then on by pressing and holding the button until the
desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the button until the desired speed is reached,
then release it.
Thedirectionofairowcanbechangedfromdownwardto
upward or from upward to downward.
To reverse the airow:
1.Makesurethe is on.
2. Press the button.
Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
LIGHT CONTROL
ON - OFF
A momentary press of
the LIGHT button
TO CHANGE BRIGHT-
NESS
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
SECOND
To turn the lights off and on, press and release the button for less
than one second.
To vary the light brightness:
1. With lights off, press and hold the button. After one second the
lightscomeonattheirlowestlevelandgraduallybecomebrighter.
2.Releasethebuttonwhenthedesiredbrightnesslevelisreached.
Thebrightnesslevelisnowinthefanmemoryandwillautomaticallycome
onatthesamebrightnessthenexttimethe button is used. To
maintainthislevelofbrightness,pressthe button for less than
one second. To lower the brightness, turn the lights off, then press and hold
the buttonuntilthedesiredbrightnesslevelisreached.Whenthe
lightison,youmayincreasethebrightnesslevelbypressingandholding
the buttonuntilthedesiredlevelisreached,thenreleaseit.
FAN CONTROL
ON - OFF
A momentary press
of the FAN button
TO CHANGE SPEED
Press and hold FAN
button longer than
one second
INTELI•TOUCH OPERATION
POWER
INTELI•TOUCH OPERATION
SPEED CONTROL
INTELI•TOUCH
•
REVERSING AIRFLOW
INTELI•TOUCH
LIGHT
AUTOMATIC DEMONSTRATION PROGRAM
FAN
FAN
+
+++
FAN
LIGHT
FAN
LIGHT
FAN
FAN
LIGHT
FAN
FAN
FAN
FAN
FAN
REVERSE
LIGHT
LIGHT
LIGHT
LIGHT
LIGHT
R
POWER
POWER
POWER
R
 previous next