Filter
Top Products
2011 Portable Spa
LTR20111000, Rev. D
Operating Your Spa
www.calspas.com
16
high speed may be started.
Jets 2
Press the “JETS 2” button once to turn pump 2 on or
off and to shift between low and high speeds if it is a
two-speed pump. If left running, the pump will turn
off after 15 minutes.
Option
This is an optional feature. Press the “OPTION” button
to turn the optional equipment on and off. If left on,
the equipment will automatically turn off after 15
minutes.
Light
Press the “LIGHT” button to turn the spa light on and
off and to shift between dim and bright settings if
your light is dimmable. On dim, the control panel will
show the center circle plus one quarter of the light
beams. Half of the light beams will show on medium
brightness, and all of the light beams will show on
bright.
Invert
Press the “INVERT” button to change the numbers
in the display to read upside down. Another press
returns the display to the right-side-up position. This
enables you to read the display while you are in the
spa.
Locking the Panel
To lock the panel:
Press “TIME”, “JETS 1”, and the “UP” button within •
three seconds. When locked, the panel will display
“LOCK”. All buttons are frozen except the “TIME”
button.
To unlock the panel:
Press “TIME”, “JETS 1” then the “DOWN” button •
within three seconds.
Setting the Temperature Lock
To activate the temperature lock:
Press the “UP” or “DOWN” button, “TIME”, “JETS •
1”, then the “UP” button within three seconds.
The panel will display “TEMP LOCK” when the set
temperature is locked.
To unlock the set temperature:
Press the “UP” or “DOWN” button, “TIME”, “JETS •
1”, and then the “DOWN” button.
Time
When time hasn’t been programmed, the “TIME” icon
ashes. To set the time, press the “TIME” button and
then the “MODE/PROG” button. Use the “UP” and
“DOWN” buttons to adjust time. See the next page
for more detailed instructions.
Standard, Economy, Sleep, and Standby
Modes
Mode/Prog: This button is used to switch between
standard, economy, and sleep modes.
Press “MODE/PROG” to enter mode 1.
programming.
Press the “DOWN” button to cycle through to the 2.
desired mode.
Press “MODE/PROG” to conrm selection.3.
Standard Mode: Standard mode maintains the desired
temperature. The last measured spa temperature
displayed is current only when the pump has been
running for at least two minutes. STAND will display
until the mode is changed.
Economy Mode: Economy mode heats the spa to
the set temperature only during lter cycles. ECON icon
will display until the mode is changed. Pressing the
“JETS 1” button while in economy mode puts the spa
in standard-in-economy mode, which operates the
same as standard mode but reverts back to economy
mode automatically after one hour. During this time,
pressing the “MODE/PROG” button will revert to
economy mode immediately.
Sleep Mode: Sleep mode heats the spa to within
20°F (11°C) of the set temperature only during lter
cycles. SLEEP will display until the mode is changed.
Standby Mode: Pressing “Warm” or “Cool” then
“JETS 2” will turn off all spa functions temporarily. This
is helpful when changing a lter. Pressing any button
resets the spa.
Jets 1
Press the “JETS 1” button once to turn pump 1 on
or off and to shift between low and high speeds if
equipped. If left running, the low speed turns off
after two hours and the high speed turns off after 15
minutes. On non-circulation systems, the low speed of
pump 1 runs when the blower or any other pump is
on. It may also activate for at least two minutes every
30 minutes to detect the spa temperature and then to
heat to the set temperature if needed, depending upon
the mode. When the low speed turns on automatically,
it cannot be deactivated from the panel; however, the