Filter
Top Products
(HD:fE :'("-:L- RfPLACEMIN:T
'OIIEPAIR
'~:,
~
cable rqller brDck-et 9nd down to tl1e right hole in the
top of the blower housing-
C. Turn the cable pulley with the c;able boit toward the
bottom of the blower housing.
D. Put the e~s of the;:csble UP throug~ the hoj~s in the
bottom of the dable p~'ley and croSs the ends up and
Over the cable bolt and Und~r the washer. Pull the
cable 1;ight and tighten 'the cable'bolt and nut, making
sure the cable remains in the track around the cabJe
'PiJlley,
E.S1ide cable p\11ley back Into plac&,
F. Tighten cable with adjusting cable boIL
5.
REPLAce THE BLOWER HOUSING
A. Reverse the steps outlined 'In Step' '1 'to replace the
bio\/,!er housing and parts to the Snow Th(ower,
.
1. REMOVE T."E BLOWER HOU$tl'l!U FROM .:rHE
MACHiNe;
A. 'Remove the roai~~iI~d and d~nnec.t the reel."drive
chain at fh,e{;~~fn t;Orinecting lInk. :;
8. Remove ~. fout c&r~iageb~lts;fastenin9 the ~oop
~o the m~l,!ntin~: t,ir~c;kE!:t$: Remo\f& the sc;oop and
reel ~~mt;llyint8ci, no rot remoVe ,mol,jiiting
brackets frt!)tn tl:an:i~estr~ps;
c. Remove th~SPtm9p:inandreTQye fan.
D. Loosen chute chain to allow for removal of blower
housihQ.
E. Rem9~t) the bI9~~( l)ou~,ln.9 f.ro~ tryeunit. ,
~2.
R~MOVE THe WORN CABLE.
A. Place the blower housing on a bench with the cable
,.pulle:Y ex;posfld;: , : ': ;,.
8. Re~ove th~ cable roller ~over.
C, Loo~n the lock bolt on top of tl1e cable roller
bracket and adjust the cable adjusting bOliandtabie
roller in as far as possible.
: ,p~ lif~ ~he ~~ble pulley a~ay fr~~ t.h~ blower hOusing
';. .~Pr:~xj~8~ly3- incheg.
.E. LQasen: the cabte moun1ing bo'it andrernove the Qble
."
~rJds from thecablepuHey. "
F. I..oo~n m$ nut on the cable ~:as~ir WhiOI:1 h9(d~ the
table to 'the upper W<>ut 8ssemb,ly ar:l4,'remove the
worn c~ble. "
3;
REPLACE ~~w ~A~LE: '-.
: A, Fasten a loop in center of the cableUilder the cable
, ,
Was~e( lfiakiffg.cer1air that bdth:ends of th!;! cable are
~ven-. , --, '- ' ,
8, With the cable crossed, wrap each end of the Cable
around the upper spout.
4.:~LACIN9
TtiENEWCABL£ OVER THE CABLE
R()LLERS.
A. ~9tate th~:up~r ';pout asiiiembly witht~e disCharge
side ilj:tfiti.oppOsite qir&ci.io~from the c~ble:pulley
~ide 01 th~ bloWer housing; "
8; Exte~d th& ~ble f,rbm tJ:le.,fight ~ide 01:-t1)6 .upper
, Spout qssembiyover the to!liiron the left side -of the
q~bfe roller bracketandttlrough th&let~c;:~bJe.hole in
.
thfj top of the blower !j?uSlrig'. Ext~nd':t6e cable from
the left sid!1 ()f the ~out assemblyacros$ the c~nt;er
table roller, b:ack f)nd around the cab'&" adjustment
roller and over the t:able yo"ertJr'\ the right side of the
14