Filter
Top Products
18 Owner Service
MAN0475 (9/21/2005)
Figure 13. Belt Routing
BELT SERVICE
Belt Replacement
One of the major causes of belt failure is improper
installation. Before installing a new belt, check the fol-
lowing:
1. Check pulley shafts and bearings for wear.
2. Check pulley grooves for cleanliness.
3. Make sure spindles turn freely and without wobble.
If grooves require cleaning, moisten a cloth with a non-
flammable, non-toxic degreasing agent or commercial
detergent and water.
Avoid excessive force during installation. Do not use
tools to pry belt into pulley groove. Do not roll belt over
pulleys to install. This can cause hidden damage and
premature belt failure.
Belt Installation
1. Disconnect idler spring from deck lug I.
2. Slide belt under drive pulley A and over idler arm.
Position belt around drive pulley A.
3. Loosen bolt holding belt guide G and swing it away
from pulley B. Route belt around pulley B, idler C
and pulley D as shown.
4. Make sure belt is on drive pulley A, route around
idler F, and connect idler spring to lug I on deck.
5. Grasp belt between spindle pulley E, spring loaded
idler F and spindle pulley D. Pull spring loaded idler
with belt to obtain enough belt length to route it
over pulley E. Make sure spring-loaded idler pivots
freely with belt installed.
IMPORTANT
■ Use care when installing or removing belt from
spring-loaded idler at step 5. Springs store energy
when extended and, if released suddenly, can
cause personal injury.
6. Adjust belt guide G to provide 1/16" to 1/8"
clearance from belt. Tighten bolt to 85 lbs-ft.
BLADE SERVICE
Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
Keep all persons away from o( )12.1(v6.i3.1(v64(e)-7.7(53D0]TJ/49(t(s)4.8-7.7(ee)-7.7lr)6.3(om)]TJ-1.4771 -1.385468D0.0347 Tc0.024r7(l)34( alllo)75.5(c)2(rlel)34( alp f)6.3 b)-m of-13.5(o(c)2(n)-5.(orn(c)2(g f)6.3 (l)34( ad(c)2(d)-1)6.3f)-5.95(oe1(a)084(en)7.4(,en)-5.173 b)-m o1.7(,at)-6.2(o(a)084r(a)4.6(n)]TJ0 -1.31330Tm0.0029 Tc.9(rte(s)3(t4.7(9-0.3(3(t4.e8(t)6.VIC1 g105.Tc525.T96 386.42 22 1/97.32 1qC1 i 105.Tc74796 6 386.42 -22 1/97.32W* n1qC386.4199 Tr10 22 1/901 Tm105.T79663525.T96 Tccm/Im20 DoQQ0 g37 7534396 5204.7600249987.32 155.084 419.1 TD.439 Tm2)-7.7.32 13(a)6 419.1 TD5204.760029 Tm.32 13(a)6 419.36TD.439 T12)-7.7.32 11 g 0 95 31)-48T121 )12 26.Tm.32 1/GS2 gs1.2 re12 ]TJ/F413305 1 Tf413305 8 T.95Tc22045968Dm0 g3374 ( SERVIC0025 0 4 0.C1 i 42)6.57220462 m42.6(54220462 l428.54225.789 l4n)7127220462 l432.097220462 l435347 2)04687 l432.89 2)04687 l436.7 TD226.434 l429.635 2)04687 l42u)7.762)04687 l42.9(96 226.434 l424.19162)04687 l422.0572 SERVIC44omg