Filter
Top Products
4 Introduction
MAN0670 (11/16/2007)
SPECIFICATIONS
3-Point Hitch: HC48, HC54, HC60, HC72 . . . . . . . . . . . . . . . . . . . . . . . Category 1 & 2
Cutting Height. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1" - 9"
Blade Spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Number of Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Heat Treated Alloy Steel
Blade Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CCW
Tractor PTO RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
Universal Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Category 3
Side Frame Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Ga
Tailwheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4" x 16"
GENERAL INFORMATION
Some illustrations in this manual show the
equipment with safety shields removed to provide
a better view. This equipment should never be
operated with any necessary safety shielding
removed.
The purpose of this manual is to assist you in operating
and maintaining your cutter. Read it carefully. It fur-
nishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.
The illustrations and data used in this manual were cur-
rent at the time of printing, but due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
Throughout this manual, references are made to right
and left directions. These are determined by standing
behind the equipment, facing the direction of forward
travel. Blade rotation is counterclockwise as viewed
from the top of the cutter.
HC48
HC54 HC60 HC72
Cutting Width 48" 54" 60" 72"
Overall Width 52" 58" 64" 76"
Weight (Approximate) w/Shear Bolt 428 lbs 474 lbs 538 lbs 604 lbs
Weight (Approximate) w/Slip Clutch 439 lbs 485 lbs 549 lbs 615 lbs
Blade Speed (Feet per minute) 13,028 14,657 14,335 14,963
Gearbox 1:1.92 1:1.92 1:1.69 1:1.47
Recommended Maximum Tractor HP 15 - 40 15 - 40 20 - 50 20 - 50
(Rev. 2/15/2008)