DS11 User Manual ◄ 7
The safety tag (p/n 15875) at right is attached to
the tool when shipped from the factory. Read and
understand the safety instructions listed on this tag
before removal. We suggest you retain this tag and
attach it to the tool when not in use.
12412
Warning Decal
28409
Composite Decal
L
WA
108
29530
Failuretousehydraulichoselabeledandcertified
asnon-conductivewhenusinghydraulictoolson
ornearelectriclinesmayresultindeathor
Forproperandsafeoperationreadownersmanual
andmwkesurethatyouhavebeenproperly
trainedincorrectproceduresrequiredforwork
seriousinjury.
onoraroundelectriclines.
ELECTROCUTION
HAZARD
DANGER
12412
E
40LPM @138 BAR
EHTMACATEGORY
12535
D
30LPM @138BAR
EHTMACATEGORY
11207
7-9 GPM / 26-34 LPM
DO NOT EXCEED 2000 PSI / 140 BAR
•DO NOT EXCEED SPECIFIED FLOW OR PRESSURE •USE
CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM.
•USE OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM.
•CORRECTLY CONNECT HOSES TO TOOL ‘IN’ AND ‘OUT’
PORTS. •IMPROPER HANDLING, USE OR MAINTENANCE
OF TOOL COULD RESULT IN A LEAK, BURST OR OTHER
TOOL FAILURE. •CONTACT AT A LEAK OR BURST CAN
CAUSE OIL INJECTION INTO THE BODY. •FAILURE TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY.
10-14 GPM / 38-53 LPM
DO NOT EXCEED 2000 PSI / 140 BAR
•DO NOT EXCEED SPECIFIED FLOW OR PRESSURE •USE
CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM.
•USE OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM.
•CORRECTLY CONNECT HOSES TO TOOL ‘IN’ AND ‘OUT’
PORTS. •IMPROPER HANDLING, USE OR MAINTENANCE
OF TOOL COULD RESULT IN A LEAK, BURST OR OTHER
TOOL FAILURE. •CONTACT AT A LEAK OR BURST CAN
CAUSE OIL INJECTION INTO THE BODY. •FAILURE TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY.
03786 DS113000 03790 DS115000
03786
GPM Sticker (DS113000)
03790
GPM Sticker (DS115000)
12535
Circuit “E” Decal – DS115000 Only
11207
Circuit “D” Decal – DS113000 Only
71073
71073
CE Tool Plate
29530
Sound Level Decal
28409
SAFETY TAG P/N 15875 (Shown smaller then actual size)
DANGERDANGER
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CER-
TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
BEFORE USING HOSE LABELED AND CERTIFIED AS NON-
CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR-
RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY
DEPARTMENT INSTRUCTIONS.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC-
TION INTO THE BODY OR CAUSE OTHER SEVERE
PERSONAL INJURY.
A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
CAUSE A LEAK OR BURST.
B. DO NOT EXCEED RATED WORKING PRESSURE OF
HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
PRESSURE MAY CAUSE A LEAK OR BURST.
C. CHECK TOOL HOSE COUPLERS AND CONNECTORS
DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH
YOUR HANDS. CONTACT WITH A LEAK MAY RESULT
IN SEVERE PERSONAL INJURY.
IMPORTANT
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE
MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
REVERSING CONNECTIONS MAY CAUSE REVERSE
TOOL OPERATION WHICH CAN RESULT IN SEVERE
PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
TECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST
ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY
TRAINED PERSONNEL.
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
TOOL STICKERS & TAGS