Filter
Top Products
4
101241
!
WARNING ICON G 001
SAFETY WARNINGS
Continued
7. Secure wood you are cutting by using clamps or chocks.
8. Grip chain saw firmly with both hands. Never operate chain
saw with one hand. Never use hand guard as handle.
9. Keep finger off trigger until ready to make cut.
10. Before starting chain saw, make sure chain is not touch-
ing anything.
11. Avoid body contact with grounded objects such as pipes,
wire fences, and metal posts.
12. Keep all parts of body away from chain when saw is running.
13. Do not force chain saw while cutting. Apply light pressure.
14. Cut small brush and saplings with extreme care. Slender
material may catch in chain and be whipped toward you.
This could also pull you off balance.
15. When cutting limb or tree trunk that is under tension, use
extreme caution. Be alert for wood springing back. When
wood tension is released, limb could spring back and
strike operator causing severe injury or death.
16. Do not activate the chain brake to stop saw. Always
release trigger to stop saw.
17. Carry chain saw from one place to another
• with chain saw unplugged
• by holding front handle (never use front hand guard as
handle)
• with finger off trigger
• with guide bar and chain to rear
• with scabbard in place
MAINTENANCE AND STORAGE OF CHAIN SAW
1. Unplug chain saw from power source
• when not in use
• before moving from one place to another
• before servicing
• before changing accessories or attachments
2. Inspect chain saw before and after each use. Check saw
closely if guard or other part has been damaged. Check
for any damage that may affect operator safety or
operation of saw. Check for alignment or binding of
moving parts. Check that switch turns motor on and off.
Check chain brake. Check for broken or damaged parts.
Do not use chain saw if damage affects safety or opera-
tion. Have damage repaired by authorized service person.
3. Maintain chain saw with care.
• Never expose saw to rain.
• Keep chain sharp, clean, and lubricated.
• Follow steps outlined in this manual to sharpen chain.
• Keep handles dry, clean, and free of oil.
• Keep all screws and nuts tight.
• Inspect power cord often. If damaged, have repaired by
authorized service person.
• Never carry chain saw by power cord.
• Never yank power cord to unplug it.
• Keep power cord from heat, oil, and sharp edges.
• Inspect extension cords often and replace if damaged.
4. When servicing, use only identical replacement parts.
5. Always store chain saw
• in a high or locked place, out of children’s reach
• in a dry place
• in a carrying case or with scabbard over guide bar
Keep this manual for reference. It is your guide to safe and
proper operation of this chain saw.
bars listed in this manual.
• Never use dull or loose chain. Keep chain sharp and
tensioned correctly.
Saw Maintenance and Kickback Safety
Follow maintenance instructions in this manual. Proper
cleaning of saw and chain and guide bar maintenance can
reduce chances of kickback. Inspect and maintain saw after
each use. This will increase the service life of your saw.
Note:
Even with proper sharpening, risk of kickback can increase
with each sharpening.
PUSHBACK AND PULL-IN
Cause Of Pushback and Pull-In
Pushback may occur while cutting with top of guide bar.
Pushback will force saw back towards you. Pull-in may occur
while cutting with bottom of guide bar. Pull-in will force saw
in towards wood you are cutting. These hazards can occur if
chain is pinched, caught, or contacts a non-wood object.
The following steps will reduce the risk of pushback or pull-in:
• Use both hands to grip saw while saw is running. Use firm
grip. Thumbs and fingers must wrap around saw handles.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance.
• Stand slightly to left side of saw. This keeps your body
from being in direct line with chain.
• Have saw running at full speed before starting a cut.
• When cutting, make sure spike of saw is against wood
(pull-in only). See Product Identification, page 5, to locate
spike.
• Never try cutting through two logs at same time. Only cut
one log at a time.
• Watch for shifting of log or other forces that may pinch
chain.
• Use extreme caution when re-entering a previous cut.
• Do not twist saw when removing guide bar from undercut.
• Use wedges made of plastic, wood, or light alloy (never steel
or iron) to hold cut open.
CHAIN SAW OPERATION
1. Stay alert. Use common sense while operating chain saw.
2. Keep work area clean. Cluttered areas invite injuries.
3. Be aware of extension cord while operating chain saw. Be
careful not to trip over cord.
4. Keep children, animals, and bystanders away from chain
saw and extension cord. Only chain saw user should be in
work area.
5. Do not cut down a tree unless you are trained or have
expert help.
6. If two or more persons perform bucking and felling
operations at the same time, provide plenty of distance
between operations. Provide distance of at least twice the
height of tree being felled.
!
WARNING ICON G 001
WARNING
Avoid pushback and pull-in. These hazards can
cause you to lose control of chain saw.
Pushback or pull-in can cause severe injury.