Jacuzzi DESIGNER BATH SERIES Hot Tub User Manual


 
ENGLISH
20
Jacuzzi Whirlpool Bath K339000X 3/06
OPERATION
NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features dis-
cussed in this instruction pamphlet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained
after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold
water continuously like pools or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath
dealer for the complete line of whirlpool spas available.
Once the bath is installed, remove any residue or foreign materials left over from construction. Paint, tar, or other difficult surface
stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). NOTE: Use these chemicals only on
SURFACE stains. Other dirt can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or
plastic edge; do not use metal scrapers, wire brushes or other metal tools, as they will damage the bath's surface.
1" - 2"
FILL TO AT LEAST
1" - 2" ABOVE HIGHEST JET
WATER RAINBOW
FILL SPOUT (OPTIONAL)
DRAIN/OVERFLOW
(OPTIONAL)
FULLY ADJUSTABLE JETS
T
YPICAL BATH FITTINGS
SUCTION
COVER
ELECTRONIC CONTROL PANEL
OPERATING INSTRUCTIONS
Controlling Whirlpool Action
The whirlpool action in your bath, controlled manually and
electronically, is influenced by three factors – direction of flow,
force of water, and force of air. Every bath manufactured by
Jacuzzi Whirlpool Bath that is equipped with fully adjustable
PowerPro
®
jets, are manually adjustable for direction and water
force. Some baths have additional jets which can be adjusted
for direction only. Baths equipped with 2 speed motors and
electronic controls can also influence water force and force
of air.
Direction: To change the direction of the water flow, swivel
the jet nozzle to the desired angle. The jets can be directed
individually toward any location on your body to provide a
hydromassage. The jets can also be adjusted so that they all
point in the same direction (clockwise or counterclockwise)
to circulate the water in a circular motion around the bath,
causing a total whirlpool effect.
Water Force: The high volume, fully adjustable PowerPro
®
jets can be manually adjusted to control the force of the water
coming into the bath. For robust action, increase the force of
the flow by rotating the jet handles to the left (counterclock-
wise). For a more gentle effect, rotate the handles to the right
(clockwise). Customize water force by lowering water volume
of one (1) jet(s) to increase water force in another jet(s). In
units with 2 speed motors the water force can be increased or
decreased using the electronic control. Never run the whirl-
pool system with all the jets closed.
Force of Air: Force of air is controlled electronically. Re-
fer to the Control panel instructions for details in adjusting
force of air.
Water Level
Close the drain and fill the bath until water is at least 1" to
2" (2,5 - 5,08 cm) above the highest jet (see water line indi-
cated in the illustration). Do not turn on the whirlpool sys-
tem at any time if the jets are not completely immersed in
water. Do not immerse the control panel by overfilling
the bath. Running the whirlpool system when there is insuf-
ficient water in the bath could result in water spraying outside
the bath area. Running the whirlpool system without water
will damage the recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop
below the jets which could result in water being sprayed out
of the unit. To prevent this, you must turn unit off before
exiting bath.
DIRECTIONALLY
ADJUSTABLE
FULLY
ADJUSTABLE
JETS