Jacuzzi DESIGNER BATH SERIES Hot Tub User Manual


 
ENGLISH
19
Jacuzzi Whirlpool Bath K339000X 3/06
Drain Information
A drain/overflow assembly (sold separately) must be in-
stalled on the bath, water tested, and connected to the sani-
tary system of the house. After opening the carton, inspect
for damage and verify that the kit is of the proper finish. In the
Jacuzzi Whirlpool Bath drain/overflow kit, note that the waste
flange, strainer, overflow cover and cover screws are pack-
aged in a separate package within the kit to protect the trim
finish. Follow the installation instructions provided with the
drain/overflow kit. After the drain is fully installed, test for
proper drainage. If the unit does not drain properly, rectify
this condition before proceeding with the installation. Jacuzzi
Whirlpool Bath is not responsible for removal and or reinstal-
lation costs.
NOTE: Watertight installation of the drain is the installer's
responsibility. Drain leakage is excluded from the Jacuzzi
Whirlpool Bath warranty of this product.
Plumbing
Pump, jets, and suction fittings for the whirlpool system
are factory plumbed in schedule 40 PVC piping.
All Jacuzzi Whirlpool Bath products are factory tested for
proper operation and watertight connections prior to shipping.
If leaks are detected, notify your Jacuzzi Whirlpool Bath dealer.
Do not install the unit.
Water Supply
Consult local authorities for plumbing code requirements
in your area.
IMPORTANT: Proper installation of the fill spout plumb-
ing and compliance with local codes are the responsibil-
ity of the installer. Jacuzzi Whirlpool Bath does not war-
rant connections of water supply fittings and piping, fill
systems, or drain/overflow systems. Nor is it responsible
for damage to the bath which occurs during installation.
CAUTION: A nonflammable protective barrier must be
placed between soldering work and bath unit to prevent
damage to the bath.
Shower Information
Because of some baths' unique contour design, a rigid
shower door cannot readily be installed. If a shower is de-
sired, we recommend a hand-held shower be installed in con-
junction with a shower curtain, as this will allow the user to
control the direction of the spray.
NOTE: Proper installation of a shower is the responsibil-
ity of the installer. Jacuzzi Whirlpool Bath is not respon-
sible for damage to the unit or for water damage which
might occur due to its installation.
Anti-Siphon Valve
Optional Anti-Siphon valve installation. Anti-Siphon valve
is not supplied with the tub. Consult your local plumbing code
requirements for the minimum height above the tub rim.
COLD
WATER
SUPPLY
1/2" NOM.
ELL (TYP)
DIVERTER HANDLE
RECOMMENDED WATER SUPPLY CONNECTIONS
(NOT ALL REQUIRE OR HAVE ALL FEATURES SHOWN)
ANTI-SIPHON VALVE
BATH RIM
6"
HOT WATER SUPPLY
WATER RAINBOW® FILLSPOUT
THESE ITEMS SHOWN
FOR EXAMPLE ONLY
1/2" MPT x 1/2" MPT x 18" FLEXIBLE
1/2" NOM. COPPER (TYP.)
1/2" NOM. TEE
3/8"x1/2"
NOM. ELL (2)
3/4" FPT x 5/8" O.D.
COMPRESSION
3/8" FPT x 1/2"
NOM. COUPLING
1/2" FPT x 3/8" NOM.
ADAPTER
SHOWER HOSE 1/2" FPT
Consult local authorities
for plumbing code
requirements in your area.
Plumbing and Water Supply
Clean-Up After Installation
To avoid dulling and scratching the surface of the bath, never use abrasive cleaners. A mild liquid detergent and warm water
will clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools will scratch the surface. Spots left by plaster or grout can be
removed if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult surface stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol).
NOTE: Use these chemicals only on SURFACE stains.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper.
You can restore the glossy finish to the acrylic surface of the bath with a special compound, Meguiar's #10 Mirror Glaze. If that
is not available, use automotive rubbing compound followed by an application of automotive paste wax.
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Ask your Jacuzzi Whirlpool Bath
dealer for special instructions or visit our web site at http://www.jacuzzi.com/. To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF