Filter
Top Products
Make sure to wipe up any spilled fuel be-
fore starting the engine.
Store gasoline in a clean, approved con-
tainer and keep the cap in place on the
container.
TO STOP ENGINE
• To stop engine, move the throttle control
lever to O (STOP) position and remove
key. Keep the key in a safe place. The
engine will not start without the key.
NOTE: DO NOT turn key.
TO START ENGINE (Electric Starter)
Be sure that the engine has sufficient oil.
The snow thrower engine is equipped with a
120 volt A.C. electric starter and recoil
starter. Before starting the engine, be cer-
tain that you have read the following infor-
mation:
COLD START
• Be sure the auger drive and traction drive
levers are in the disengaged (released)
position.
• Move the throttle control to '_ (FAST)
position. See figure on page 9.
• Remove the keys from the plastic bag.
Insert one key into the ignition slot. Be
sure it snaps into place. DO NOT TURN
KEY. Keep the second key in a safe
place.
' Rotate the choke knob clockwise to H
choke ON position. See figure on page 9.
• Connect the power cord to the switch box
on the engine.
Z_ CAUTION: This starter is equipped
with a three-wire power cord and plug
and is designed to operate on 120 volt AC
household current. It must be properly
grounded at all times to avoid the possibility
of electrical shock, which may be injurious
to operator. Follow all instructions carefully
as set forth in the "To Start Engine' section.
Determine that your house wiring is a three-
wire grounded system. Ask a licensed elec-
trician if you are not sure. If your house wire
system is not a three-wire system, do not
use this electric starter under any condi-
tions. If your system is grounded and a
three-hole receptacle is not available at the
point your starter will normally be used, one
should be installed by a licensed electrician.
When connecting 120 volt AC power cord,
always connect the cord to the switch box
on the engine first, then plug the other end
t2
into the three-hole grounded receptacle.
When disconnecting power cord, allVays
unplug the end in the three-hole grounded
receptacle first.
• Plug the other end of the power cord into
a three-hole, grounded 120 volt A.C.
receptacle.
• Push the primer button while covering the
vent hole as follows: (Remove finger
from primer button between primes).
See figure on page 9 for location.
Do not prime if temperature is above
5O°F.
Two times if temperature is 50°F to 15°F.
Four times if temperature is below 15°F.
• Pt_sh down on the starter button until the
engine starts. Do not crank for more than
10 seconds at a time. This electric starter
is thermally protected. If overheated it will
stop automatically and can be restarted
only when it has cooled to a safe tem-
perature (a wait of about 5 to 10 minutes
is required).
• When the engine starts, release the
starter button and move choke lever to
_1/2 choke" position. When engine runs
smoothly, move choke lever to "No
Choke" Position.
• Disconnect the power cord from the
receptacle first and then from the switch
box on engine.
NOTE: Allow the engine to warm up for sev-
eral minutes before blowing snow in tem-
peratures below 0°F.
• Run the engine at full throttle '_p (FAST)
when throwing snow.
TO STOP ENGINE
• To stop engine, move the throttle control
lever to O (STOP) position and remove
key. Keep the key in a safe place. The
engine will not start without the key.
NOTE: DO NOT turn key.
TO START ENGINE (Recoil Starter)
Be sure that the engine has suff=clent oral.
The snow thrower engine is equipped with
a recoil starter. Before starting the engine,
be certain that you have read the following
information: