2010 Portable Spa
LTR20101001, Rev. B
Cleaning and Maintenance
www.calspas.com
33
Fast Sheen (Spa nish protecting wax)
Cal Spas™ Fast Sheen is an essential part of maintaining
your spa’s nish. Through normal use, the spa’s nish
can accumulate dirt, oil, and calcium, causing a rough
feel and unsightly scum lines. Cal
Spas™ Fast Sheen is a non-oil based
wax that is specically formulated
to protect the spa’s nish from the
chemicals and minerals associated
with normal spa use.
The most effective solution to minimize
cleaning time is prevention. When the
following steps are followed, the spa’s
nish will actually start to resist most
of the elements that cause calcium build-up and make
scum line clean-up easier.
Prior to Spa Start-Up and Relling
Spray Cal Spas™ Multi-Purpose Cleaner directly to 1.
the spa’s nish.
Wipe clean with a soft cloth.2.
Repeat on heavily calcied areas.3.
Wipe spa thoroughly with a wet sponge, rinsing 4.
often in a bucket of clean water.
Allow the spa to dry completely.5.
Apply a coat of Cal Spas™ Fast Sheen to the spa’s 6.
entire nish with a soft cloth or sponge.
Allow Fast Sheen to dry until white and powdery.7.
Buff clean with a soft cloth, rotating frequently.8.
IMPORTANT: Cal Spas™ Fast Sheen should not be used
on spas full of water. Only apply to clean, cool, dry
surfaces. Incorrect product usage may cause water
clarity issues.
Cleaning and Replacing the
Filter
Filtration
Filtration is one of the most important steps you can
take to ensure clean, clear water. Regardless of what
some people may think, it is far less expensive to
x water clarity problems by ltering your spa than
by using excessive amounts of chemicals, excessive
ltration times, or by water replacement.
Cal Spas™ ltration system draws contaminated water
through the exclusive Bio-Clean™ lter removing
debris from the water. It then pumps the newly
cleaned water back into the spa through various jets.
Spas equipped with the optional Quest 2000 Ozonator
will also receive ozone injection into the ltered water
for further protection against contaminants during
ltration cycles. Filtration also ensures that chemicals
are mixed thoroughly through the water, increasing
performance.
Filtration starts on electronically controlled spas as
soon as the pumps are primed and water ow is
steady. As the ow of water goes through the lter, dirt
and debris is removed and accumulated in the lter
cartridge. As the lter cartridge accumulates dirt and
debris, water ow is restricted and jet performance is
reduced. This can cause your spa to not run or heat
effectively.
Clean your lter regularly and replace as needed.
Filter Cleaning
Your new Cal Spa has been designed for quick and
easy lter maintenance. The lter cartridge should be
cleaned once a week. These instructions apply to both
dual and single ltration systems.
Turn the power off at the breaker.1.
Remove the lter by turning it counterclockwise 2.
and unscrewing the bottom threads. Then pull it
up and out.
Clean the lter with a garden hose as follows:3.
Hold the lter vertically.a.
Spray the lter cartridges with a pressure b.
nozzle, starting from the top and spraying
down each pleat.
Turn the lter cartridge over and repeat Step c.
3b.
Deep clean lter cartridge every month. Use d.
only a Cal Spas™-approved lter-cleaning
chemical.
Exclusive Bio-Clean™ Filter Cartridge
The lter cartridge is designed to remove dirt, sand,
minerals, phosphates, bather waste and other solids
from the spa. Unfortunately, some spa owners fail
to include lter cleaning as part of their chemical
maintenance plan. Filters accumulate debris and
become prime areas for bacteria growth.
The Cal Spas™ exclusive Bio-Clean™ Filter is the
only antibacterial lter cartridge on the market today.
Having a lter cartridge that prevents bacteria growth
is added protection for those times you forget to clean
the lter. We recommend that you only replace your
spa’s lter cartridge with a Bio-Clean™ lter cartridge
for ensured protection and peace of mind.