Ariens 921001 - ST824E, 921002 - ST1027LE, 921003 - ST1130DLE, 921004 - ST924DLE Snow Blower User Manual


 
GB - 5
ALWAYS check overhead and side clearances
carefully before operation. ALWAYS be aware of traffic
when operating along streets or curbs.
Keep children and people away. Keep children out of
work area and under watchful care of a responsible
adult.
NEVER allow children to operate or play on or near
unit. Be alert and shut off unit if children enter area.
DO NOT allow adults to operate unit without proper
training. Only trained adults may operate unit. Training
includes actual operation.
Keep area of operation clear of all toys, pets, and
debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or floors. Avoid
uneven work areas and rough terrain. Stay alert for
hidden hazards.
DO NOT operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if a wheel is
over the edge of a cliff or ditch, or if an edge caves in.
Falling snow, fog, etc. can reduce vision and cause an
accident. Operate unit only when there is good visibility
and light.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation requires
your complete and unimpaired attention at all times.
NEVER allow anyone to operate this unit when their
alertness or coordination is impaired.
DO NOT operate unit without wearing adequate winter
outer garments. Wear adequate safety gear, including
safety glasses with side shields, and protective gloves.
Wear proper footwear to improve footing on slippery
surfaces.
DO NOT wear loose clothing or jewelry and tie back
hair that may get caught in rotating parts.
Protect eyes, face and head from objects that may be
thrown from unit. Wear appropriate hearing protection.
Avoid sharp edges. Sharp edges can cut. Moving parts
can cut off fingers or a hand.
ALWAYS keep hands and feet away from all rotating
parts during operation. Rotating parts can cut off body
parts.
NEVER place your hands or any part of your body or
clothing inside or near any moving part while unit is
running.
ALWAYS keep hands away from all pinch points.
DO NOT touch unit parts which might be hot from
operation. Allow parts to cool before attempting to
maintain, adjust or service.
Never direct discharge towards persons or property
that may be injured or damaged by thrown objects. Use
extreme caution on gravel surfaces. Stay alert for
hidden hazards or traffic. Adjust Runners so Scraper
Blade does not contact gravel.
DO NOT throw snow any higher than necessary.
Deflected materials can cause injury and property
damage.
Always stand clear of the discharge area when
operating this unit.
Fumes from engine exhaust can cause injury or death.
DO NOT run engine in an enclosed area. Always
provide good ventilation.
ALWAYS disengage attachment, stop unit and engine,
remove key and allow moving parts to stop before
leaving operator’s position.
ROTATING AUGER CAN CAUSE SERIOUS INJURY.
NEVER ATTEMPT TO UNCLOG OR CLEAN UNIT
WHILE ENGINE IS RUNNING.
Read, understand, and follow all instructions in the
manual and on the machine before starting.
Understand:
How to operate all controls.
The functions of all controls.
How to STOP in an emergency.
Before starting engine, disengage control(s).
Use only approved extension cords and receptacles
when starting units equipped with electric starter. DO
NOT connect electric starter cord to any wiring system
that is not a three-wire grounded system.
ALWAYS allow unit and engine to adjust to outdoor
temperatures before clearing snow.
DO NOT overload the machine capacity by attempting
to operate or to clear snow at too fast a rate.
Slow down and turn corners slowly.
Do not operate in reverse unless absolutely necessary.
ALWAYS back up slowly. Always look down and behind
before and while backing.
Disengage attachment drive when traveling from one
work area to another.
Abnormal Vibrations are a warning of trouble. Striking a
foreign object can damage unit. Immediately stop unit
and engine. Remove key and wait for all moving parts
to stop. Remove wire from spark plug. Inspect unit and
make any necessary repairs before restart.
Before cleaning, removing clogs or making any
inspections, repairs, etc.: disengage clutch(es), stop
unit and engine, remove key, allow moving parts to
stop. Allow hot parts to cool.
Run unit a few minutes after clearing snow to prevent
freeze-up of attachment.
Disengage attachment when not in use. Disengage all
clutches before starting engine. Adjust runners to clear
gravel or crushed rock surfaces safely.
Never leave a running unit unattended. ALWAYS shut
off engine before leaving unit. ALWAYS remove key to
prevent unauthorized use.