Filter
Top Products
EN - 22
6. 920014, 020 – Insert key into ignition
switch on engine and rotate into "Run"
position.
920013, 021 – Insert key into ignition
switch on engine and push into "Run"
position. DO NOT twist key after it is
inserted.
7. Grasp recoil starter handle and pull rope
out slowly until it pulls harder. Let rope
rewind slowly.
8. Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
IMPORTANT: DO NOT let Recoil Starter
Handle snap against Starter.
9. Repeat steps 7 and 8 until engine starts.
(If engine does not start, refer to
TROUBLESHOOTING on page 39.)
10. Adjust choke as needed.
11. 920014, 020 – Set throttle to Part
Throttle or Slow position for adaptation
to outside temperature or travel. Set
throttle to Fast position for normal
operation.
Electric Start (120V)
1. Connect extension cord to starter.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
2. Plug extension cord into 120V 3-wire,
grounded outlet.
IMPORTANT: Use an extension cord that is
capable of handling current requirements.
Cord should be rated for a minimum of
13 amps, grounded, UL listed, CSA certified
and labeled as suitable for outdoor use.
3. Turn discharge chute straight ahead.
4. Make sure that the attachment clutch
and traction drive clutch levers are fully
disengaged.
5. Push Primer Bulb 2 or 3 times for cold
engine.
NOTICE: When temperature is below -15° F
(-26° C) additional priming may be needed.
6. If engine is cold, apply choke. See
Engine Manual for detailed instructions.
NOTICE: A warm engine requires less
choking than a cold engine.
7. 920014, 020 – Set throttle to proper
starting position.
920013, 021 – Toggle ignition switch to
"Run".
8. 920014, 020 – Insert key into ignition
switch on engine and rotate into "Run"
position.
920013, 021 – Insert key into ignition
switch on engine and push into "Run"
position. DO NOT twist key after it is
inserted.
9. Press starter button on engine until
engine starts.
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to TROUBLESHOOTING on
page 39.)
10. Adjust choke as needed.
11. Disconnect power cord from outlet, then
starter.
12. 920014, 020 – Set throttle to Part
Throttle or Slow position for adaptation
to outside temperature or travel. Set
throttle to Fast position for normal
operation.
Shut Off
1. Release Traction Drive Clutch Lever and
allow unit to come to a complete stop.
2. Run Impeller a few minutes after use to
prevent freeze-up of Impeller.
3. Release Attachment Clutch Lever and
wait for all moving parts to come to a
complete stop.
4. Toggle or rotate ignition switch to "Stop"
position.
5. Remove key.
SNOW REMOVAL
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperature before clearing
snow.
NOTICE: Attachment clutch should be
engaged before traction drive clutch when
throwing snow.
1. Select Speed Control position and
direction.
2. Engage Attachment Clutch – Right Hand
Lever.
3. Engage Traction Drive Clutch – Left
Hand Lever.
IMPORTANT: DO NOT overload unit capacity
by attempting to clear snow at too fast a rate.
Use slow speed to clear deep or hard packed
snow.
Tips for Operation
Snow is best removed as soon as possible
after snow fall.
To clear an area, run unit in an overlapping
series of paths. For large areas, start in the
middle and throw snow to each side, so snow
is not cleared more than once.
ALWAYS direct snow away from area to be
cleared and with direction of the wind.