26 Sp
1
2
3
4
5
6
7
8
9
10
11
12
14
15
17
18
19
20
23
26
27
28
29
30
31
32
14
13
16
24
25
21
22
Para Ordenar Repuestos o Asistencia Técnica, Sírvase Llamar al
Distribuidor Más Cercano a Su Domicilio
Sírvase darnos la siguiente información:
- Número del modelo
- Número de Serie o código con fecha (de haberlo)
- Descripción y número del repuesto según la lista de repuestos
Puede escribirnos a:
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
Manual de Instrucciones y Lista de Piezas
Pistola Pulverizadora HVLP Alimentada por Gravedad
34
FAN DIRECTION
The direction of the fan (horizontal or
vertical) can be changed by loosening
the lock ring and turning the air cap 90
degrees (See Figure 3). Hand tighten
lock ring after adjustment.
PATTERN ADJUSTMENT
1. Adjust air pressure to the spray gun
according to the recommendations
supplied with the spray material.
This air pressure usually falls
between 40 - 60 psi.
Do not
exceed
spray gun maximum pressure.
Adjust air pressure with the trigger
pulled and air control knob (if applic-
able) fully open. If reduced air pres-
sure is desired for some areas of the
spray job, use the air compressor reg-
ulator or air control knob to reduce
pressure as necessary (See Figure 4).
2. Set pattern size to desired shape.
For full pattern, open pattern con-
trol knob by turning counterclock-
wise. For a round pattern, turn pat-
tern control knob clockwise
(See Figure 5).
3. Turn fluid control knob fully clock-
wise until closed (See Figure 5).
4. Trigger a short burst while turning
fluid control knob counterclockwise.
Observe the spray pattern on the tar-
get and adjust the fluid control knob
until the desired pattern (atomiza-
tion) is obtained (See Figure 6).
If the spray is too fine (excessive over-
spray), caused by too much air for the
amount of paint being sprayed, reduce
the air pressure or open the fluid con-
trol to spray more material.
If the spray is too coarse (spitting globs),
reduce the amount of material with the
fluid control knob or thin the paint.
5. The fluid control knob can be used
to finely adjust pattern consistency.
Before spraying the workpiece, practice
a few minutes on a cardboard target to
ensure the pattern size and consistency
are set correctly.
Operation
1. Begin spraying.
Always keep
the gun at
right angles to
the work (See
Figure 8).
2. Keep the noz-
zle about 6 to
9 inches from
the work sur-
face through-
out the stroke
and always
keep the gun
WATER/OIL IN COMPRESSED AIR
All compressor pumps discharge some condensed water, oil or contaminates with
the compressed air.
IMPORTANT: This condensation will cause “fish eyes” to appear in the paint
job. Install appropriate water/oil removal equipment and controls as necessary
for the intended application. Locate filter as close to spray gun as possible.
Failure to install appropriate water/oil removal
equipment may result in damage to machinery or
workpiece.
Operating Instructions and Parts Manual HVLP Gravity Feed Spray Gun
Figure 3
Horizontal Fan
Vertical Fan
Air Cap
Lock Ring
Figure 4 - Air Adjustment on Spray Gun
Increase
Air Flow
Decrease
Air Flow
Air Control
Knob
Figure 5 - Pattern Size
Pattern control knob
Fluid control
knob
Figure 7 - Gravity Feed Spray Gun
Vent Hole
Fluid Control Knob
Trigger
Fluid Tip (Nozzle)
Pattern Control Knob
Cup
Air Cap
1/4” NPS Air Inlet Fitting
Fluid Packing Nut
Air Valve Packing Nut
3
Correct
Paint too
coarse
Paint too
fine
Figure 6 - Pattern Consistency
(Atomization)
Preparation (Cont.)
6 - 9”
Figure 8
33
Juego de tapa de prueba HVLP
Los juegos de recipiente de prueba no
incluyen manómetros. Es necesario comprar
por separado un juego de manómetros de
baja presión certificados, de 1/8” NPT.
36
1.6 mm
1.4 mm
35
