Filter
Top Products
35
RQT6866
Timer operations and convenient functions
34
RQT6866
Timer operations and convenient functions
A
1
3
ECHO 1-MIC-2
13
KARAOKE
V.MUTE
MONO L
MIC VOL
MIN MAX
ECHO
VOLUME
UP
DOWN
MONO
R
ECHO
Enjoying karaoke (For Australia and N.Z.)
You can do karaoke with CDs and tapes.
Preparation:
Lower the volume with [MIC VOL] and connect the microphone.
Use a dynamic microphone.
Plug type: 6.3 mm monaural
1 Press [KARAOKE] to select a voice mode.
Each time you press the button:
MONO L>MONO R>VOICE MUTE>off (Normal)
^---------------------------------------------------------------}
≥Karaoke CDs and tapes
MONO L: Only left channel sound (No vocal)
MONO R: Only right channel sound (Vocal)
Select no vocal for karaoke. Vocal and no vocal may be reversed.
≥Normal music CDs and tapes
VOICE MUTE: Voice mute (Lowers vocal volume)
2 Start playing the CD or tape.
3 Adjust the main volume and microphone volume.
To cancel
Press [KARAOKE] to clear the display.
To record your performance
Start recording in deck 2 and then start singing.
Ensure the voice mode is set to off (at step 2 above) when playing the
recording.
Note
The karaoke modes cannot be used with the radio, SUPER 3D AI EQ, 6CH
DISCRETE INPUT or surround effects.
When using the VOICE MUTE function
≥Voice mute may not function sufficiently or noise may interfere when using
the following software.
≥Monaural software
≥Software with few musical instruments, including classic music and
poetry recitations
≥Software with duets or strong choruses
≥VOICE MUTE reduces the level of the vocals but does not cancel them
out completely.
ªA
Using the echo effect
Press [ECHO].
Each time you press the button:
ECHO 1>ECHO 2>ECHO 3>OFF
^----------------------------------------------------}
Original display
A
DISPLAY MODE
DISPLAY MODE
B
C
DIGITAL
S.WOOFER
AV EFFECT
SLEEP
CH SELECT
3D AI
PROGRAM
1
23
4
56
7
890
CANCEL
DISC
VCR/AUX/
6CH INPUT
TAPE/
DECK 1/2
SUPER
SOUND EQ
TUNER/
BAND
2/;
1∫
MUTING
45
j
VOLUME
i
EQ
Î
PRO LOGIC
SUPER SRND
TEST
VOLUME
MUTING
MUTING
PHONES
a
b
c
Í
CD
DISPLAY
X
sALBUM
W
S10/-/--
ªA Changing the sound range display
The sound processor shows the level of each sound range with the three
types of display described below.
Press [DISPLAY MODE].
The spectrum display will change as follows.
[a] Normal display
This display indicates the strength of the sound in each tonal range.
[b] Peak-hold display
The peak sound value of each sound range is held on the display for
about one second after it occurs.
[c] Aurora display
The peak sound value of each sound range is displayed in inverted
form.
ªB Muting the volume
Remote control only
Press [MUTING].
Volume is reduced to minimum.
To cancel
Press [MUTING] again.
“MUTING” goes out and the volume is restored.
To cancel from the tuner/amplifier, turn [VOLUME] to minimum (–– dB),
then raise it to the required level.
Muting is also canceled when the unit is turned off.
ªC Using headphones (not included)
Reduce the volume before connection.
Avoid listening for prolonged periods of time to prevent hearing damage.
Plug type: 3.5 mm stereo
(On the sound processor)