Filter
Top Products
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating your
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask
over the spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 7)
Your tractor is equipped with anoperator presence sensing
switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
o Depress clutch/brake pedal into full "BRAKE" position
and hold.
• Place parking brake !ever in"ENGAGED" position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parking brake
wi!l hold tractor secure.
PARKING BRAKE ATTACHMENT CLUTCH I
"ENGAGED" POSITION SWITCH PULL OUT TO
I
"ENGAGE"
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas.
&
CAUTION: Always stop tractor com-
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL (See Fig. 7)
Always operate engine at full throttle.
* Operating engine at less than full throttle reduces the
battery charging rate.
, Full throttle offers the best mower performance.
'HROTTLF_/CHOKEI
CONTROL
"BRAKE"
POSITION
E
-_"DIS ENGAGED" LEVER
POSITION
CLUTCH/BRAKE HEIGHT
PEDAL "DRIVE" ADJUSTMENT
POSITION KNOB
FIG. 7
STOPPING (See Fig. 7)
MOWER BLADES -
• Move attachment clutch switch to "DISENGAGED"
position.
GROUND DRIVE -
• Depress clutch!brake pedal into full "BRAKE" position.
- Move gearshift lever to neutral (N) position.
ENGINE -
o Move throttle control to slow (,,gb) position.
NOTE: Failure to move throttle control to slow (,_!,)
TO MOVE FORWARD AND BACKWARD
(See Fig. 7)
The direction and speed of movement is controlled by the
gearshift lever.
o Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
• Move gearshift lever to desired position.
- Slowly release clutch/brake pedal to start movement.
IMPORTANT: BRINGTRACTORTOA COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE.
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 7)
The cutting height is controlled byturning the height adjust-
ment knob in desired direction.
• Turn knob clockwise (fN) to raise cutting height.
o Turn knob counterclockwise (_-_) to lower cutting
height.
The cutting height range is approximately 1-1/2" to 4% The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
- The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
position and allowing engine to idle before stopping may ....
cause engine t0 "bac_ire". ........ lawns, mow or[en-ana ar_er moa_ral:_rgro_n.-- ..........
• For best cutting performance, grass over 6 inches in
, Turn ignition key to "OFF" position and remove key. height should be mowed twice. Make the first cut
Always remove key when leaving tractor to prevent
unauthorized use. relatively high; the second to desired height.
• Never use choke to stop engine.
13