Filter
Top Products
-- 3 --
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
D
Never p lace any object in the air intake open-
ing a s this could restrict p ro per air f low a nd
cause damage to the un it.
D
Never use for s preadingchemicals, fertiliz-
ers,orother s ubstanceswhich maycontain
toxic materials.
D
To av oidspreadingfire,donot usenearleaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
D
Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D
Have all maintenance other than the rec-
ommended proceduresdescribed in thein-
struction manual performed by an autho-
rized service dealer.
D
Disconnect s park plug befo re performing
maintenance except for carburetor adjust-
ments .
D
Use only recommended Poulan
!
replace-
ment parts;use ofany otherparts may void
your warranty and cause damage to your
unit.
D
Empty f uel tank b efore storing the unit. Use
upfuel left incarburetor bystarting eng ine a nd
letting it run un til it stops .
D
Do not use any accessory or atta chment
other than th ose recommended by manufac-
turer for use with your unit.
D
Do notstore the unitor fuel in aclosed area
where fuel vapors can reach sparks or an
open flame from hot water heaters,electric
motors or switches, furnaces, etc.
D
Store in a dry area out of reach of children.
SPECIAL NOTICE:
Exposure to vibra-
tions throughprolongeduse of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people proneto circulation disorders
or abnormal swelling. Prolonged use in cold
weatherhas beenlinked tobloodvessel dam-
agein otherwise healthypeople. Ifsymptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance o f these
problems. Users who operatepower tools on
a continual and regular basis must monitor
closely their physical condition andthecondi-
tion of this tool.
SPECIALNOTICE:
For users on U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443),Idaho,Maine,Minnesota,New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on for est,
brush,and/orgrasscoveredlandin theabove
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working o rder, o rtheengine must becon-
structed, equipped, and maintained for the
prevention o f f ire. Checkwith your s tateor lo-
cal authorities for regulations pertaining to
these requirements. Failure to follow these
requirementsis aviolation o fthelaw.This uni t
is not factory equipped w ith a spark arresting
screen; however, a spark arresting screen is
available asanoptional part.Ifa spark arrest-
ing screen is required in your area, contact
your authorized s ervice dealer for t hecorrect
kit. Thespark arrestingscreen, blowertubes,
and nozzles must be assembled to unit to be
in full compliance with regulation s .
ASSEMBLY
W ARNING:
Stop engine and be sure
the impeller blades hav e stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing m aintenance or ac-
cessing movable parts.
W ARNING:
If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
D
A standard screwdriver is required for as-
sembly.
BLOWER TUBE ASSEMBLY
1. Align the rib on the blower tube with the
groove i n the blower outlet; slide the tube
into place.
NOTE:
Knobmust belooseenough toallow
blower tube to be inserted in blower outlet.
Loosen knob by turning counterclockwise.
Blower
T ube
Blower
Outlet
Rib
Groove
2. Securethetubeby turningthe knobclock-
wise.
3. To removethetube,turntheknobcounter-
clockwise to loosen the tube; remove the
tube.
VACUUM BAG ASSEMBLY
1. Open the zipper on the vacuum bag and
insert the elbow tube.
2. Push the small end of the elbow tube
through the small opening in the bag.