Filter
Top Products
9
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING POSITION
ALWAYS WEAR:
Long P ants
Boots
Eye Protection
Cut from your left t o your right.
When operating unit, clip shoulder strap onto
clamp, stand as shown and check for the fol-
lowing:
S
Wear eye protection and heavy clothing.
S
Extend your left arm and hold handlebar
grip with your left hand.
S
Hold throttle grip with your right hand with
finger on throttle trigger.
S
Keep unit below waist level.
S
Keep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
S
Maintain full weight of tool on your left
shoulder.
S
Without bending over, keep the blade or
trimmer head near and parallel t o the
ground and not crowded into material being
cut.
OPERATING INSTRUCTIONS FOR
USE WITH TRIMMER HEAD
WARNING:
Always wear eye protec-
tion. Never lean over the trimm er head. Rocks
or debris can ricochet or be thrown into eyes
and face and cause blindness or other serious
injur y.
Before trimming, bring engine to a speed suffi-
cient to cut material to be trimmed.
Do not r un the engi ne at a h igher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower s peeds, there is less engine noise and
vibration. The cutting line will last longer and w ill
be less likely to “w eld” onto the spool.
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
To stop engine:
S
Release the throttle trigger.
S
Push and release the engine ON/STOP
switch.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
in. (5 cm) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
To advance line:
S
Operate the engine at full t hrottle.
S
Hold the trimmer head parallel to and above
the grassy area.
S
Tap the bottom of the trimmer head lightly
on the ground one time. Approximately 2 in.
(5 cm) of l ine will be advanced with each
tap.
Always tap the trimmer head on a grassy
area. Tapping on s urfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.If the line is worn down to 2
inches (5 cm) or less, more than one tap will
be required to obtain the most efficient line
length.
WARNING:
Use only 0.095
!
(2.4
mm) diameter line. Other sizes of line will not
advance properly and can cause serious
injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off dur-
ing cutting and become a dangerous missile
that can cause serious injury.
CUTTING METHODS
WARNING:
Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S
The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
S
The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds , but it also can cut the tender
bark of t rees or shrubs and scar fences.
S
For trimming or scalping, use less than fu ll
throttle to increase line life and decrease
head wear, especially:
S
During light duty cutting.
S
Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S
For mowing or sweeping, use full throttle for
a good clean job.