Filter
Top Products
- 46 -
Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope
at or near the Sun. Do not look through the telescope as it is moving.
MAINTENANCE
LX200R telescopes are precision optical instruments designed to yield a lifetime of
rewarding applications. Given the care and respect due any precision instrument, your
LX200R will rarely, if ever, require factory servicing. Maintenance guidelines include:
a. Avoid cleaning the telescope’s optics: A little dust on the front surface of the tele-
scope’s correcting lens causes virtually no degradation of image quality and
should not be considered reason to clean the lens.
b. When absolutely necessary, dust on the front lens should be removed with gen-
tle strokes of a camel hair brush or blown off with an ear syringe (available at any
pharmacy). DO NOT use a commercial photographic lens cleaner.
c. Organic materials (e.g., fingerprints) on the front lens may be removed with a
solution of 3 parts distilled water to 1 part isopropyl alcohol. You may also add 1
drop of biodegradable dishwashing soap per pint of solution. Use soft, white facial
tissues and make short, gentle strokes. Change tissues often.
Caution: Do not use scented or lotioned tissues or damage could result
to the optics.
d. Do not, for any reason, remove the correcting plate from its machined housing for
cleaning or other purposes. You will almost certainly not be able to replace the
corrector in its proper rotational orientation and serious degradation of optical per-
formance will result. Meade Instruments assumes no liability for damage incurred
to the telescope in this way.
e. If the
LX200R is used outdoors on a humid night, water condensation on the
telescope surfaces will probably result. While such condensation does not
normally cause any damage to the telescope, it is recommended that the entire
telescope be wiped down with a dry cloth before the telescope is packed away.
Do not, however, wipe any of the optical surfaces. Rather, simply allow the tele-
scope to sit for some time in the warm indoor air, so that the wet optical surfaces
can dry unattended.
f. If your
LX200R is not to be used for an extended period, perhaps for one month
or more, it is advisable to remove the batteries from the telescope. Batteries left
in the telescope for prolonged periods may leak, causing damage to the tele-
scope’s electronic circuitry.
g. Do not leave your
LX200R inside a sealed car on a warm summer day; excessive
ambient temperatures can damage the telescope’s internal lubrication and elec-
tronic circuitry.
h. The microfocuser is carefully adjusted at the factory. If it becomes necessary to
adjust the microfocuser ball bearings (see Fig. 34), it must be performed by fac-
tory trained technicians. If the microfocuser is improperly adjusted, performance
will degrade and damage will result. Damage due to improper adjustments not
authorized by the factory will not be covered under warranty.
Collimation
The optical collimation (alignment) of any astronomical telescope used for serious pur-
poses is important, but in the case of the Advanced Ritchey-Chrétien telescope design
of the
LX200R models, such collimation is absolutely essential for good performance.
Take special care to read and understand this section well so that your LX200R will
give you the best optical performance.
As part of final optical testing, every Meade Advanced Ritchey-Chrétien telescope is
precisely collimated at the Meade factory before shipment. However, vibrations in
shipping can cause the optical system to become misaligned. Re-aligning the optics
is, however, a straightforward process.
To check the collimation of your
LX200R, center a bright star that is overhead, or use
a “hot spot” of reflected Sunlight from a chrome car bumper, with the supplied 26mm
eyepiece. Allow the telescope to adjust to the temperature of your observation site
before proceeding; temperature differences between the optics and the outside air
can cause distortion in the images.
Fig. 34: Microfocuser ball bearings.