Filter
Top Products
16
Section 4: Operating Instructions
RCR1542 and RCR1548 Rotary Cutters 312-556M
11/25/15
Table of Contents
Section 4: Operating Instructions
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in the operation, transport, storage, and
maintenance of the Rotary Cutter. Therefore, it is
absolutely essential that no one operates the cutter
without first having read, fully understood, and become
totally familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:
• Important Safety Information, pages 1 to 5
• Section 1: Assembly and Set-Up, page 8
• Section 3: Adjustments, page 14
• Section 4: Operating Instructions, page 16
• Section 5: Maintenance & Lubrication, page 20
Also make sure the operator has completed the
Operating Checklist below before using the cutter.
Safety Information
!
DANGER
Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.
!
DANGER
Tractor PTO shield, gearbox shaft shield, and driveline
shields must be secured in place when operating cutter to
avoid injury or death from entanglement in driveline.
!
DANGER
Always disconnect driveline from tractor PTO shaft before
servicing underside of cutter. If tractor is started with PTO
engaged, the cutter can cause bodily injury or death.
!
DANGER
Keep others away while cutter is operating. It can discharge
objects at high speeds. Therefor, the use of front and rear
safety guards is required when cutting along highways and in
areas where people may be present. Stop blade rotation if a
bystander is within several hundred feet.
Operating Checklist
✔
Check Page
Make sure all guards and shields are in place.
Refer to "Important Safety Information".
Page 1
Read and follow hook-up & preparation instructions.
Refer to "Section 1: Assembly and Set-Up". Page 11
Read and make all required adjustments.
Refer to "Section 3: Adjustments". Page 14
Lubricate cutter and driveline as needed.
Refer to "Lubrication Points".
Page 24
Make sure all gearboxes are properly lubricated and
that all oil plugs have been replaced properly.
Refer to Gearbox lubrication.
Page 24
Check cutter initially and periodically for loose bolts
and pins. Refer to “Torque Values Chart”. Page 30
!
DANGER
All guards and shields must be installed and in good working
condition at all times during cutter operation.
!
DANGER
Do not operate a broken or bent driveline. Such drivelines can
break apart while rotating at high speeds causing serious
injury or death. Always remove Rotary Cutter from service
until damaged drivelines are repaired or replaced.
!
DANGER
Never place hands or feet under the deck or attempt to make
adjustments to the cutter with PTO engaged. Cutter blades
rotating at high speeds cannot be seen and are located close
to the deck housing. Body extremities can be cut off instantly.
!
DANGER
Do not operate and/or travel across steep inclines where a
tractor can rollover resulting in serious injury or death.
Consult your tractor’s manual for acceptable inclines the
tractor is capable of traveling across.
!
DANGER
Do not use cutter as a fan. Cutting blades are not properly
designed or guarded for this use. Using cutter as a fan can
result in injury or death.
!
WARNING
Always disengage PTO, put tractor in park or set park brake,
shut tractor engine off, remove ignition key, and wait for all
moving parts to stop before dismounting from tractor.
!
WARNING
Always disengage PTO before lifting cutter up and never
operate cutter in the raised position. The cutter can discharge
objects at high speeds resulting in serious injury or death.
!
WARNING
Keep blade bolt access hole covered at all times except when
servicing cutter blades. Make sure driveline is disconnected
from the tractor before servicing cutter blades.
!
WARNING
Never allow riders including children on the tractor or cutter.
They can fall and be ran over causing serious injury or death.
!
WARNING
Always disengage PTO before lifting cutter too high and never
engage PTO with cutter raised too high. Doing so can cause
rotating u-joints to break into pieces that can be thrown at
high speeds causing serious injury or death.