Filter
Top Products
1.03 - Assembly Instructions for Model SS1023B
CAUTION: Stand clear of bands when cutting as they could be under sufficient tension to
cause them to fly loose. Take care in removing bands and wire. They often have extremely
sharp edges and cut very easily.
NOTE: Assembly will be easier if all parts are loosely assembled before tightening the hardware. All
hardware needed for assembly will be found in the hardware bag or on the machine.
Each unit is shipped with a hardware bag that consists of the following:
1Hairpin cotter Ø5 (5BP0041291)
3Washer fender Ø8 (5BP0014514)
4Washer flat Ø8 (5BP0015230)
8Nut HH M08-1.25 C6 Z TK (5BP0001806)
1Nut HH M30-2.00 C6 Z TN (5BP501651B)
2Bolt HH M08-1.25x16 C8.8 Z F (5BP0046454)
3Bolt CR M08-1.25x25 C4.6 Z (5BP501663B)
1Threaded bushing (5BP501622B)
2Bushing cat.0/1 for tractor arms (5BP0014710); serial #XF...287132 & below only
Hardware bag contains the following:
1Driveline
1Flow control assembly (#5, fig. 2)
1Guard (#4, fig. 2)
1Stirrer (#8, fig. 2)
1Mobile shutter (#10, fig. 2)
1Spreader disc (#11, fig. 2)
Model SS1023B Qty.Description
To assemble the spreader do the following:
1. Attach spreader disc (see #11, fig. 2) to output shaft of gearbox securing it with the hairpin cotter
(see #27, fig. 2).
2. Install guard (see #4, fig. 2) with scale label facing up to the brackets on the spreader frame.
Attach it to the frame using two M8x16 bolts (see #22, fig. 2), four Ø8 flat washers (see #19, fig.
2) and two M8 nuts (see #21, fig. 2).
3. Insert threaded bushing (see #9, fig. 2) through hopper bottom (see #3, fig. 2). Attach mobile
shutter (see #10, fig. 2) to threaded bushing and secure with nut (see #26, fig. 2).
4. Slide hopper and onto the output shaft of the gearbox. Secure hopper to frame using three M8x25
carriage bolts (see #18, fig. 2), three Ø8 fender washers (see #20, fig. 2), and six M8 hex nuts
(see #21, fig. 2).
5. Install flow control assembly (see #5, fig. 2) into slot in mobile shutter at the bottom of the hopper.
6. Secure location of the shutter lever by tightening the two knobs (see #6, fig. 2).
7. Install the stirrer (see #8, fig. 2) using M8x35 hex bolt (see #24, fig. 2), two Ø8 flat washers (see
#19, fig. 2), and one M8 elastic stop nut (see #25, fig. 2) that are already bolted to the stirrer.
8. Tighten all hardware.
9. Install driveline and ensure it has at least 2” from bottoming out in its shortest working position and
has the minimum 6” overlap in its longest working position. Refer to Section 4.03
1
of this manual,
if it is determined that the driveline is too long and needs to be shortened. Contact your local
dealer if it is determined that the driveline is too short for your tractor.
FERTILIZER SPREADERS OPERATOR’S MANUAL
GENERAL INFORMATION 5 FRONTIER
1
See Section 4.03 - Driveline, for instructions on how to determine correct driveline length and procedures for
shortening the driveline.