Filter
Top Products
• Loosen the 4 fixing screws and remove
the side cover.
• Using the 19 mm key, loosen the
tensioner screws.
• Using a lever, tighten the belt. If the belt is
not tight enough, bear on the motor, then
again on the tensioner.
• Each saw is fitted with a pump in order to
eliminate dust and overheating.
• The blade is cooled automatically as the
machine starts.
13
Blade cooling
12
Changing the belt
• The machine is set before leaving the
factory and no adjustment is necessary.
• However, after shocks, loosening of nuts
and bolts, or sharp movements when
tilting the head, if necessary adjust the
stop screws (J) and check the squareness
(for straight cuts).
14
Adjustments
• Retighten the nuts and bolts periodically.
• In the event of a long period of use pay
special attention to the maintenance and
protection of the disc.
• Make sure that sufficient water is sprayed
onto the disc.
• Tighten the disc correctly.
• Make sure that the contact faces of the
disc, the flanges and the spindle are
clean.
15
Important advice
12
The manufacturer declines all
responsibility for loss or damage
resulting from misuse or any
modification, alteration or
powering that does not conform
to the manufacturer's original
specifications.
At the work station, the sound
pressure level may exceed 85 db
(A)
In this case individual protection
measures must be taken.
16
Repairs
Contact your supplier who is
entirely at your service to carry
out repairs in the shortest time at
the best possible price.
S
A
V
17
Spare parts
For rapid delivery of spares and in order to
avoid any wasted time, it is necessary to
remind your supplier of the details shown
on the instruction plate on the machine with
each order, as well as the reference of the
part to be replaced.
The instructions for use and spare parts
found in this document are for information
only and are not binding.
As part of our product quality improvement
policy, we reserve the right to make any
and all technical modifications without prior
notice.
In the event of deterioration and
scrapping of the machine, the
following items must be
disposed of in accordance with
the requirements of the
legislation in force.
18
Scrapping
• Main materials :
- Motor : Aluminium (AL), Steel (AC),
Motor : Copper (CU), Polyamide (PA)
- Machine : Steel sheet (AC)
- Machine : Cast iron (FT)
FAULT FINDING
In the event of faulty operation refer to the
tables below to find a solution.
• The machine does not work
CAUSES
Not plugged in
properly or cable
damaged
No mains voltage
Switch defective,
motor cable
damaged
Motor faulty (no
power, unpleasant
smell)
- Make sure that
the supply is
correctly plugged
in (plug,
extension lead,
etc)
- Check the supply
cable
- Test or have
tested by an
electrician
(circuit breaker,
plug, etc)
- Have tested by
an electrician or
contact the
service
department
- Contact the
service
department to
have the motor
replaced
REMEDIES
• Difficult starting
CAUSES
Single phase motor
starting condenser
Three-phase
supply not correct
(on 2 phases,
motor cable faulty)
- Replace the
condenser
- Have it checked
by an electrician
or contact the
service
department
REMEDIES
• The pump does not start
CAUSES
The mains lead is
not correctly
connected or is
damaged
No voltage in pump
circuit or mains
supply circuit
- Check the mains
lead
- Check the pump
circuit and mains
supply circuit
REMEDIES
• The pump does not pump water
CAUSES
An air bubble may
have formed inside
the pump body
The turbine is
jammed
- Holding the pump
of the outlet pipe
remove it from
the water and
reimmerse it
- Unscrew the filter
and, using a
small
screwdriver,
remove all dirt
from the
operating area of
the turbine.
REMEDIES
English
See exploded view
00000000 (0)
Item number Quantity