Filter
Top Products
14 – English
Mowing secondary areas
To set the Auto Mower in the operating mode “mow secondary
area” enter the command
*
33 # when the mower is in the
charging station. The Auto Mower will reverse out and stop
immediately in front of the charging station when it is fully
charged.
Now move the Auto Mower to the secondary area. When the
mower is started it will run until the entire battery is discharged
(this takes about 1,5-2,5 hours) and will then signal “cannot find
charging station”. The Auto Mower must then be returned to the
charging station by hand. The operating mode “mow secondary
area” is automatically cancelled.
You can also cancel the operating mode “mow secondary area”
by using the command
*
34 # before the battery is discharged.
By moving the Auto Mower back to the working area where the
charging station is located it will seek out the charging station
itself when necessary.
USE
If you want it to leave via either of two symmetrical sectors, for
example 85–90° and 265°–275°, enter one range of angles,
followed by
*
67 # 1 #.
For example: 85–95° and 265°–275°:
*
65 # 85 #,
*
66 # 95 #,
*
67 # 1 #.
Sector not
permitted
Sector not
permitted
80°
100°
275° 85°
95°265°
The start and stop times can be zeroed by keying in * 35 #. This
does not affect the setting of the clock.
The number of hours it takes to mow an area depends on many
factors, such as its size, the shape of the working area and the
rate of grass growth. To start off with, a suitable working time
can be calculated as 1 hour per 100 m
2
mowing area, which for
700 m
2
results in 7 hours. After you have used the Auto Mower
for a few weeks you will be able to judge whether the mowing
time should be lengthened or shortened.
Using the Auto Mower at night will require more frequent
cleaning as the grass will be damp and will then collect under
the body.
Searching for a buried boundary wire
The Auto Mower has a feature that will easily find a buried
boundary wire. Enter
*
5 # 1 and leave the cover open. Move
the Auto Mower on the front wheels using the rear handle.
When the wire sensor at the front of the Auto Mower is outside
the boundary wire the mower beeps, and when it is inside it is
silent. When it is inside the boundary wire LED 3 lights up. This
command only works when the charging station is connected.
If the mower does not detect any signal all four LEDs flash.
Reset the Auto Mower to normal operation by entering
*
5 # 0 #,
or by lowering the cover.
Leaving the charging station
See the chapter on “Installation” (Placing the charging station).
By default the Auto Mower is set to leave the charging station at
a random angle between 90° and 270°. This works well in most
gardens. If you want to choose a different angle you simply
enter the angles between which you want the mower to leave
the charging station,
*
65 # angle 1 #,
*
66 # angle 2 #.
For example: Leave between 80° and 100°:
*
65 # 80 #,
*
66 # 100 #.
The angles at which the Auto Mower sets off can be restored to
the default settings by keying in * 36 #.
To minimise wear to the lawn in front of the charging station the
mower will reverse out a slightly different distance each time it
leaves the charging station, around 52 cm +/-10 cm. It is
possible to make the mower reverse out further than or less
than 52 cm.
The reversing distance in front of the charging station can be
changed by entering * 64 # cm # where cm is 0-99 cm further
than normal and 101-130 cm is shorter than normal.
Example 1:* 64 # 20 # will make the mower reverse out 52 + 20
cm +/-
10 cm, in other words 62-82 cm.
Example 2:* 64 # 108 # will make the mower reverse out 52 - 8
cm +/-
10 cm, in other words 34-54 cm.
If you enter * 64 # 0 # the mower will reverse out 52 cm without
any variation. The factory setting is 100, i.e. the mower will
reverse out 52 cm +/-10 cm.